A place for general chat about the Jimny. Please make sure you post in the correct section on the site, this way it keeps the site tidy AND ensures you get a more relevant answer.

Suppliers/Dealers or anyone selling with a commercial view in mind CANNOT post here unless responding to a specific request of a member in a "wanted" post.

Suppliers include people "breaking for spares" on a regular basis, when purchasing spares members should ask a supplier what they contribute to the running of the forum particularly if contacted by a Private Message

Suppliers or Members who have contributed to the forum can be identifed by the
logo.

What did you do to your jimny today?

  • Lambert
  • Away
  • Moderator
  • Moderator
    Registered
  • The quickest Jimny in Harrogate...(that I own)
More
11 Jan 2023 15:55 #246821 by Lambert
Today I have mostly been getting a clean MOT, which is nice.

Temeraire (2018 quasar grey automatic)
One of the last 200ish of the gen3s, probably.
ADOS Attention Deficit Ooooh Shiny!

Please Log in or Create an account to join the conversation.

More
11 Jan 2023 16:02 #246822 by CB1289
I'm about to change my Idle Air Control Valve on my 2001 Gen 3, as my idle seems to be misbehaving!

Any last minute words of advice or encouragement for a novice would be appreciated! 

Please Log in or Create an account to join the conversation.

More
16 Jan 2023 18:45 - 16 Jan 2023 18:45 #246949 by DrRobin
Took my Jimny along a snow covered lane to test the manual hubs and Maxxis Worm-Drive tyres.



I am very happy to report that both hubs and tyres performed to expectations, there was no wheel slip in 4x4.

Looking forward to a little more snow now, fingers crossed.

Robin

2020 blue SZ5 (one of the last to be registered in the UK)
Ex 2011 Blue Jimny SZ4
Northumberland Jimny Blog

Last edit: 16 Jan 2023 18:45 by DrRobin.
The following user(s) said Thank You: Soeley, lookonimages

Please Log in or Create an account to join the conversation.

More
20 Jan 2023 13:41 #247038 by gv42
As it's snowing and cold , got the axles and arms cleaned and painted , fair bit more to do but getting there

Sent from my 2201116SG using Tapatalk
The following user(s) said Thank You: Soeley

Please Log in or Create an account to join the conversation.

More
22 Jan 2023 18:42 #247094 by Fossie
Changed the alternator .
1/2 job right? The obvious stubborn culprits , the bottom 8mm hex pivot bolt which lulls you with relative ease of undoing only to find it's a few mm longer than the gap between housing fan blades! However the wire connector wasn't for leaving its home!
The replacement unit joined in by the post for the earth being a midgesdidge further forward than the original so the strap didn't meet ....until a wire clamp was released to give it the play needed. .....and the mounting bracket . 75 mm wider .!
We won out in the end though it was a couple hours longer than hoped , with a tea break .....because if it won't work stop, have a cuppa and it slips in straightaway after!

Please Log in or Create an account to join the conversation.

More
25 Jan 2023 18:10 #247169 by gv42
Brushed off the rust , bit of zinc then black spray, getting there !

Sent from my 2201116SG using Tapatalk

Please Log in or Create an account to join the conversation.

Time to create page: 0.277 seconds
Joomla template by a4joomla
We use cookies to give you the best online experience. Please let us know if you agree to all of these cookies. Accepting the Cookies also accepts the Disclaimers for the website.