Dave's "S200KYS" Jimny 'laner Build...

Hi Lambert, sorry for the late reply, it's silly-season in our Post Office and shop this time of tear :lol:

Disk brakes seemed to be the way to go... I've been offroading Suzukis for 25+ years now, and used to suffer in the early days of pay'n'play sites that drum brakes just fill up with liquid mud... Disk brakes are fully open and wash themselves off when wading (in fresjher water!)

Braking is great, much more bite, and the ABS copes well with the different brakes on the back...

But, yes, the main advantage (to me) is indeed how much easier it is to get the shafts out and change bearings, etc...

I find it hard to believe - coming from Vitara ownership - hw difficult it is on a stock-braked Jimny?! On a Vitara the half shaft can be taken out with the drum brake backing plate still in situ - albeit with a bit of wiggling - so you don't have to disassemble the brakes to do it...

Mine's the JimnyBits kit with Megane calipers... I initially suffered from uneven wear on the pads, but JimnyBits supplied spacer shims to compensate, but since switching to TrailGear HD shafts I haven't had the issue as much?

Hope that helps...

Dave

I remebered today, there was more I meant to write about changing the bearings...

You can see in the photos that I chilled the shafts in the shop freezer overnight, and heated the ABS retaining collars in the oven until they were warm, but not hot... I don't believe this really helped, just in case anyone thinks to try it, it was still a job to hammer them on, and needed a sledge hammer in the end, as the lump hammer just wouldn't cut it...

I was banging so much that one of my neighbours wandered iver to see what the commotion was... he told me "to give it a rest", and I thought he was having a go :evil: which was strange as we've been good neighbours for many years... but :lol: he meant to give the shaft beating a break... working for BAe he reckoned all the hammering would create heat in the joint and things would get even tighter... so I fitted the offside shaft into the axle and rebuilt the brakes, and had a cuppa, and then went back to the other shaft I was struggling with, and bugger-me, a few taps with the sledge and it went home and snuggled up to the bearing?!

In hindsight, perhaps heating the ABS collar swells the inside diameter? as things warm up it's going to spread both ways isn't it?...

Just a few thoughts, might help someone out there....?

Nice one. Thanks for your thoughts. I will have to start saving . Cheers.

S200KYS wrote: I remebered today, there was more I meant to write about changing the bearings...

You can see in the photos that I chilled the shafts in the shop freezer overnight, and heated the ABS retaining collars in the oven until they were warm, but not hot... I don't believe this really helped, just in case anyone thinks to try it, it was still a job to hammer them on, and needed a sledge hammer in the end, as the lump hammer just wouldn't cut it...

I was banging so much that one of my neighbours wandered iver to see what the commotion was... he told me "to give it a rest", and I thought he was having a go :evil: which was strange as we've been good neighbours for many years... but :lol: he meant to give the shaft beating a break... working for BAe he reckoned all the hammering would create heat in the joint and things would get even tighter... so I fitted the offside shaft into the axle and rebuilt the brakes, and had a cuppa, and then went back to the other shaft I was struggling with, and bugger-me, a few taps with the sledge and it went home and snuggled up to the bearing?!

In hindsight, perhaps heating the ABS collar swells the inside diameter? as things warm up it's going to spread both ways isn't it?...

Just a few thoughts, might help someone out there....?

You probably did`nt warm up the collar enough?
I`ve only done mine once, together with a car mech friend (that has access to a press) but we did not cool down the axles (TG hd`s), only pressed on the bearing, and heated up abs collar with a induction heater ALOT. Like no F`in way you touch it with anything but tools.
Dropped right on there, all the way down. Gave it acouple hits on it to be sure it got all the way down while it cooled down, but never saw it move.
My friend said thats how they always did it at the shop on all kinds of brands with this setup.

This was the koyo kit.

I don't wish to gloat but I bought a press with saved up birthday and Christmas money from my parents, accumulated over a few years! It takes longer as you get older as you get less!

Kirkynut

All the work paid off... Great day's greenlaning from Barmouth to Corwen with Alan, Brett and Riccy & Joel today!...



Impromptu map meeting on my bonnetas we eaited for Riccy and Joel who spent the night in Bamouth before our day's adventure...



Here they are! Left to right as is the norm'... Brett in Jalapeno, me & Alan in S200KYS and Riccy & Joel in Ulysses, overloking Barmouth's estuary...





Mid-Walean for "Byway"



Quick break...



With the by-now-traditional sausage rolls perpared by Brett (1) and Mincemeat Swirls provided by my Missus...



A fallen branch..



And we soon cleared the byway with some good teamwork and my cordless chainsaw "Buzz"











Narrow bridge!







Nice descent to the valley floor!



Another awesome day out!