Tell us about your Jimny and post some pictures! Please make sure you post in the correct section on the site, this way it keeps the site tidy AND ensures you get a more relevant answer.
My Jimny named R&B
- jackonlyjack
-
Topic Author
- Offline
- Platinum Member
-
Registered
30 Jun 2020 16:16 #224293
by jackonlyjack
Replied by jackonlyjack on topic My Jimny named R&B
Time for front axle strip down
Paint my swivel's
Trailgear shafts n cv's
26 spline side gears
And new kingpin bearings if needed
Paint my swivel's
Trailgear shafts n cv's
26 spline side gears
And new kingpin bearings if needed
Please Log in or Create an account to join the conversation.
- jackonlyjack
-
Topic Author
- Offline
- Platinum Member
-
Registered
26 Jul 2020 15:06 - 07 Aug 2020 07:36 #225702
by jackonlyjack
Replied by jackonlyjack on topic My Jimny named R&B
Por15 on the swivel's
Modified landy engine mounts to fit transfer cradle
Measurements
X2 cut to fit driver side
This one cut and shaped to fit rockwatt cradle
Not sure you would need to modify for standard transfer mounts
Modified landy engine mounts to fit transfer cradle
Measurements
X2 cut to fit driver side
This one cut and shaped to fit rockwatt cradle
Not sure you would need to modify for standard transfer mounts
Last edit: 07 Aug 2020 07:36 by kirkynut.
Please Log in or Create an account to join the conversation.
- jackonlyjack
-
Topic Author
- Offline
- Platinum Member
-
Registered
29 Jul 2020 18:20 #225831
by jackonlyjack
Replied by jackonlyjack on topic My Jimny named R&B
Modified bushes fitted
While i was under their had a look at rear engine mount
Central bolt looked off to oneside
So got a new one from the spares shelf
Old one not delaminated but rubber really soft
While i was under their had a look at rear engine mount
Central bolt looked off to oneside
So got a new one from the spares shelf
Old one not delaminated but rubber really soft
Please Log in or Create an account to join the conversation.
30 Jul 2020 17:02 #225864
by Riccy
J999 MNY, ULYSSES M18 VVT with ITB's Dyno tested at 130hp
Pickup/tipper, R7me gearbox & 6.4 Rocklobster, 31" Toyo MT, 2x ARB air locker 3.9 diffs in braced axles, 6" total lift, Floating rear conversion, Raptor painted, CB, Recaro's, Caged, etc, etc...
www.youtube.com/user/riclemus
Replied by Riccy on topic My Jimny named R&B
They look a good fit 
J999 MNY, ULYSSES M18 VVT with ITB's Dyno tested at 130hp
Pickup/tipper, R7me gearbox & 6.4 Rocklobster, 31" Toyo MT, 2x ARB air locker 3.9 diffs in braced axles, 6" total lift, Floating rear conversion, Raptor painted, CB, Recaro's, Caged, etc, etc...
www.youtube.com/user/riclemus
Please Log in or Create an account to join the conversation.
- jackonlyjack
-
Topic Author
- Offline
- Platinum Member
-
Registered
30 Jul 2020 18:18 #225871
by jackonlyjack
Replied by jackonlyjack on topic My Jimny named R&B
They do fit well Riccy
Got fed up of the bolt through one's moving to one side slightly. think that's due to the bolt through's only being M8
Landy one's are M10 so no movement to be had,the transfer is lifted around 15mm higher up now
Expecting some vibration from them....but knowing they are now super strong i can live with vibration :laugh:
Got fed up of the bolt through one's moving to one side slightly. think that's due to the bolt through's only being M8
Landy one's are M10 so no movement to be had,the transfer is lifted around 15mm higher up now
Expecting some vibration from them....but knowing they are now super strong i can live with vibration :laugh:
Please Log in or Create an account to join the conversation.
Time to create page: 0.151 seconds