Dave's "S200KYS" Jimny 'laner Build...

Bit of a catch up here,enjoyed the tong and laning blogs dave similar issues to my old jimny after tong hard going.your little jim has took a beating but good to see its nearly back up and running

Daniel30 wrote: Well done Dave

I should think the A-team would have had trouble doing all that in the time

.
.
Hee hee, like they used to do, lock themselves in a barn for half a day (or three minutes in the show) and emerge with a tank made from a saloon? :laugh:
.
.

gaz3359 wrote: Bit of a catch up here,enjoyed the tong and laning blogs dave similar issues to my old jimny after tong hard going.your little jim has took a beating but good to see its nearly back up and running

.
.
Yup, think I'll stick to our "gentle" greenlaning

Yup, soon bounce back!

This is what you want....





Sadly discontinued as I understand it, but I believe an alternative is in development elsewhere

I'll wait for them!

JimnyBits or Rockwatt?

S200KYS wrote: I'll wait for them!

JimnyBits or Rockwatt?

Rockwatt did a lovely job beefing up my jimny axles as I've gone for ARB lockers front and rear. Rear hd shafts was going to be on my to do list after a Rockwatt rollcage.

I've recently had the same issues with my Jimny. I believe it was caused by running a Lockrite. I ripped off one mount and widened most of the mounts on the axle. It also ate my rear prop too.
I had a spare axle already, so swapped it over and have not re-fitted the lockrite. I'm running a standard diff now.

mc_nebula wrote: I've recently had the same issues with my Jimny. I believe it was caused by running a Lockrite. I ripped off one mount and widened most of the mounts on the axle. It also ate my rear prop too.
I had a spare axle already, so swapped it over and have not re-fitted the lockrite. I'm running a standard diff now.

I'm running an ARB air locker, so I only turn it on when I think I need it... :S

Interesting reading about the lockers, so am I right in thinking that the extra grip can put additional strain on the other parts which have then failed ?

Enjoyed the blog Dave, hope the rebuild goes well so we can get another soon

Me and my Jimny wrote: Interesting reading about the lockers, so am I right in thinking that the extra grip can put additional strain on the other parts which have then failed ?

Enjoyed the blog Dave, hope the rebuild goes well so we can get another soon

Lockrights are very hard on shafts, I switched to ARB airlockers to give the shafts an easier life but an open diff will always be better for the shafts but far less capable off road.

I run an arb locker and my mounts ripped off.

Sent from my Nexus 6P using Tapatalk

Sorted today...

Had a lie in 'til 9:30 usually up at 5:30, so that was nice :laugh: Walked the dogs with the wife for once, and then we had a cooked breakfast, so it was a leisurely 11:30 when I entered the man cave... Perfect! :lol:



Refitted the Zanfi rear Panhard Bracket to the replacement axle casing...



Got the axle reconnected to the radius arms by jacking it up to the extended bump stops to push it into place



And then fitted the new rear ProComp shocks whilst the axle was up on the bumps to check that they weren't too long when compressed, as I feared that was how the AVOs got bent... but no, a good inch and a half before the shocks would top out...?

(That's the new insert sleeve in the bottom of the ProComp shocks... it's a 10mm internal instead of a 12mm, as I use 12 grade long bolts through the bottom shock mounts)



And then with the springs at rest, to check the shocks aren't too long when fully extended, and a similar amount left...



New bolts, spring washers and "strawberry jam" :laugh:



Ready to lift the air locking diff back in...



All back together...



And a replacement prop to fit...

Sorted...

All ready for the Lake District Weekend on the 25th and 26th...

Nice,
Not going to get rockwatt to do a beefed up case for you?