A place for general chat about the Jimny. Please make sure you post in the correct section on the site, this way it keeps the site tidy AND ensures you get a more relevant answer.
Suppliers/Dealers or anyone selling with a commercial view in mind CANNOT post here unless responding to a specific request of a member in a "wanted" post.
Suppliers include people "breaking for spares" on a regular basis, when purchasing spares members should ask a supplier what they contribute to the running of the forum particularly if contacted by a Private Message
Suppliers or Members who have contributed to the forum can be identifed by the
CLICK HERE
and when you have pulled the ring forward then tuck something underneath it to stop it sprining back
Martin
Martin
2003 M13 early KAP build.
3" Trailmaster lift with 1.5 Spacers on front
Customised winch bumper and roll cage
235/85R16 Maxxis Bighorns on 16" Rims, 4:1 Rocklobster, Rear ARB locker and on-board air
Corrected arms all-round, rear disks, Recaro seats and harnesses
It will jam the hubs in the lock position which is what the original poster wanted to do.
Martin
2003 M13 early KAP build.
3" Trailmaster lift with 1.5 Spacers on front
Customised winch bumper and roll cage
235/85R16 Maxxis Bighorns on 16" Rims, 4:1 Rocklobster, Rear ARB locker and on-board air
Corrected arms all-round, rear disks, Recaro seats and harnesses
Locking the hubs locks them to the front driveshafts and prop. Therefore they will now be turning all the time when you are moving. This will increase fuel consumption and slightly stiffen the steering.
However the transfer box controls whether the front prop is connected to anything. Therefore in 2WD the front prop is still disconnected (despite turing because the front wheels are locked and turning) therefore wind up doesn't occur.
When you select 4WD the system is all locked together and yes, wind up will occur if the surface is not slippery enough
martin
Martin
2003 M13 early KAP build.
3" Trailmaster lift with 1.5 Spacers on front
Customised winch bumper and roll cage
235/85R16 Maxxis Bighorns on 16" Rims, 4:1 Rocklobster, Rear ARB locker and on-board air
Corrected arms all-round, rear disks, Recaro seats and harnesses
easy to do ... Just did ours as the vac system failed this year and I havnt got around to fitting the manual hubs yet.
just undo the 6 bolts and take the hub off ... then with finger .. lock the inner into the splines in the outer and refit. 10 min job each side.
No bits to fall out either.
Former owner of Little "Ooky", who has now started a new life in Shetland
i guess the real question is "is the vacuum system up for the task" .. the answer is generally no.
seals perish and its easy to block the filters on the actuators.. all these go towards the vacuum system failing.
Many people opt for manual hubs.. sure you have to get out and lock them manually, but you know they are locked and are not relying on listening for that telltale "Ping" and the 4x4 light on the dash.
As Martin documented, you can lock the front hubs and just use the Transfer lever to select between 2 wheel drive and 4 wheel drive. This does add drag on the car as you are turning the front drive shafts, diff and front prop shaft....
I have manual hubs but I need to overhaul them, so the easiest way for me to keep the Jimny working was to Lock the front Hubs and ignore the flashing 4x4 warning light because I know 100% that when I select 4x4, it really is sending drive to all wheels.
Former owner of Little "Ooky", who has now started a new life in Shetland
logo.
