A place for general chat about the Jimny. Please make sure you post in the correct section on the site, this way it keeps the site tidy AND ensures you get a more relevant answer.
Suppliers/Dealers or anyone selling with a commercial view in mind CANNOT post here unless responding to a specific request of a member in a "wanted" post.
Suppliers include people "breaking for spares" on a regular basis, when purchasing spares members should ask a supplier what they contribute to the running of the forum particularly if contacted by a Private Message
Suppliers or Members who have contributed to the forum can be identifed by the logo.
Suppliers/Dealers or anyone selling with a commercial view in mind CANNOT post here unless responding to a specific request of a member in a "wanted" post.
Suppliers include people "breaking for spares" on a regular basis, when purchasing spares members should ask a supplier what they contribute to the running of the forum particularly if contacted by a Private Message
Suppliers or Members who have contributed to the forum can be identifed by the logo.
stop 4x4 light flashing
14 Oct 2020 16:25 #229129
by mcgowan
stop 4x4 light flashing was created by mcgowan
my vacuum pipes have rotted away and broken off one side at the wheel i have went with manual hubs so now how can i stop the 4wd light flashing cant do it at the wheel any place under the bonnet where would be best thanks
Please Log in or Create an account to join the conversation.
14 Oct 2020 16:32 #229130
by mlines
Martin
2003 M13 early KAP build.
3" Trailmaster lift with 1.5 Spacers on front
Customised winch bumper and roll cage
235/85R16 Maxxis Bighorns on 16" Rims, 4:1 Rocklobster, Rear ARB locker and on-board air
Corrected arms all-round, rear disks, Recaro seats and harnesses
Replied by mlines on topic stop 4x4 light flashing
Put a wire loop on the vacuum sensor switch located just under the front of the battery
Martin
2003 M13 early KAP build.
3" Trailmaster lift with 1.5 Spacers on front
Customised winch bumper and roll cage
235/85R16 Maxxis Bighorns on 16" Rims, 4:1 Rocklobster, Rear ARB locker and on-board air
Corrected arms all-round, rear disks, Recaro seats and harnesses
Please Log in or Create an account to join the conversation.
14 Oct 2020 16:33 #229131
by sniper
Replied by sniper on topic stop 4x4 light flashing
On the inner wing below the battery, is the vacuum sensor, it has all the vacuum pipes going to it. Take the white two pin plug from it and bridge the two female spades with a wire bridge. That sends the vacuum present signal and stops the lights flashing.
Also remember....
Block the vacuum hoses at each calliper or water will be able to get in to the hub and goose your bearings.....
Block the vacuum line at the manifold or you will have a leak causing the engine to run poorly....
sniper
Also remember....
Block the vacuum hoses at each calliper or water will be able to get in to the hub and goose your bearings.....
Block the vacuum line at the manifold or you will have a leak causing the engine to run poorly....
sniper
The following user(s) said Thank You: X8GGY
Please Log in or Create an account to join the conversation.
15 Oct 2020 10:07 #229139
by me101
2007 Little Jim with cheap mods!
www.youtube.com/channel/UCeBDekO99Qk2aOmBmSmrI9w
Replied by me101 on topic stop 4x4 light flashing
Have a look here, there are a couple of pics to show where the bits are:
www.clsdoncaster.com/post/jimny-4wd-issue-resolved
Cheers
www.clsdoncaster.com/post/jimny-4wd-issue-resolved
Cheers
2007 Little Jim with cheap mods!
www.youtube.com/channel/UCeBDekO99Qk2aOmBmSmrI9w
The following user(s) said Thank You: lookonimages
Please Log in or Create an account to join the conversation.
Time to create page: 0.151 seconds