King pin bearing change

Changing the Kingpin Bearings

This page is a work in progress - please do not edit at this stage.

Introduction

If you off-road a Jimny (or any of the Suzuki classic 4wd vehicles) then this is a job you will become familiar with. It is also one of the worst in my opinion, not because it is difficult, but because of the smell, you will find out what I mean later.

It is also closely tied in with changing/working on the wheel bearings so some of the steps are duplicated. So what are the symptoms of worn KingPin bearings:

• Steering Shimmy, see Death Wobble
• Oil/Grease leaking from Swivel Joint
• Vertical play in the front wheel (with the car jacked up grip the wheel top and bottom and rock it, there will be movement of they are worn)

Leaking front swivel

Click on images to make them larger

It is also common not to experience any play at all and to even pass an MOT with a really bad bearing. This is because the bottom bearing in particular can rust solid so no play is detectable. The worst Jimnys for this are often the "one careful lady owner" ones that have sat for long periods on the driveway with the bottom bearing rusting away.

Changing the bearings

Tools

• Standard metric sockets and spanners
• Assorted screwdrivers
• Circlip pliers (External)
• An E10 Torx socket for the Vacuum Hub Bolts
• A ball joint splitter
• 1" Imperial Socket

The Video

Before you read the guide below you may wish to view the video. This shows the changing of the Kingpin Bearings on a Jimny fitted with ABS so you will see me remove the sensor etc.
The rest of the guide below shows the same task in a series of steps for clarity

Removing the Caliper and pads

Jimny Front Caliper

First of all secure the car, release the wheel nuts and jack up the car and remove the road wheel. This then reveals the brake caliper, this is the passenger side (nearside) caliper (UK)

Unbolting the caliper

Using a 12mm spanner, release the front caliper bolt (the left is the front of the car in this picture) and loosen the same bolt on the rear of the caliper.

Open brake caliper

The caliper then opens up using the rear bolt as a hinge.

Removing the brake pads

The pads are retained by small spring clips, a simple pull on the pads (horizontally away from the disk) should remove them (or gently prise out the pads with a small screwdriver - do not remove the spring clips). If you require new pads, spring clips or a caliper fitting kit then these are available in the BigJimny Store.

Removing the Brake Disc

Carrier bolt

The caliper is held on with two bolts at the rear (see below).

Caliper tied to Spring

Release the bolts and tie the caliper to the spring to keep it out of the way.

Disc removal using bolt

Now the front brake disc can be removed. If you are lucky it will simply pull off but if you have problems then there are two M8 holes in the disk hub. Simply run two bolts into these holes and the disk will push off the hub. The picture below shows a bolt being used to push the disk off the hub.

My disk appeared to be ok on the visible side but the rear showed some bad wear so I will change them as part of this job. New disks are available in the BigJimny Store.

• 
• 

Dismantling the Hub

Torx bolt on hub

Now the Freewheeling Hub needs to be removed. Suzuki have used Torx bolts to secure these so you will require an E10 socket to remove the bolts.

Removing the circlip

With the hub removed the driveshaft is exposed. The driveshaft is retained with a circlip so use a pair of circlip pliers to remove it. This is really fiddly and can be an annoying task. Behind the circlip is a rectangular washer that should also be removed. Note that I have also marked with white paint the orientation of the freewheeling hub, this is not strictly needed.

removing a vacuum pipe

Gently pull the two vacuum hoses for the hub from the knuckle making sure you note which one connects to each pipe. It is essential that you get this correct else the hub will not work again. Also note that if you have an ABS equipped vehicle then you will have to remove the sensor. I do not have photos of this but the video shows it. IT IS REALLY EASY TO SHEAR THE ABS BOLT - if you can I would soak it for a couple of days previously in penetrating oil.

Removing the swivel seal bolts

At the rear of the hub release the small bolts holding the seal and retainer. You can see that the swivel hub is covered in oil, a bad sign for KingPin problems.