Front fog lamps - Revision history

Bosanek: Added more OEM part numbers of other vehicle manufacturers for Valeo fog lamp 89210094

2023-02-14T11:32:51Z

Added more OEM part numbers of other vehicle manufacturers for Valeo fog lamp 89210094

Bosanek: Added alternate P.N. for fog lamp Valeo 89210094

2020-02-25T07:24:21Z

Added alternate P.N. for fog lamp Valeo 89210094

Bosanek: Added a new interwiki link

2019-12-06T09:41:41Z

Added a new interwiki link

Bosanek: Metadata correction

2019-12-06T09:39:03Z

Metadata correction

Bosanek: Lots of small additional info

2019-11-26T20:23:58Z

Lots of small additional info

Bosanek: Added P.N. of fog lamp bezels for 3rd model front bumper

2019-11-06T10:11:38Z

Added P.N. of fog lamp bezels for 3rd model front bumper

Bosanek: Typo

2019-11-04T06:34:25Z

Typo

Bosanek: Additional notes about cable connector 4 and wiring 4

2019-11-04T06:30:38Z

Additional notes about cable connector 4 and wiring 4

Bosanek: Added a picture of fog lamps and brackets mounted in a 2nd model front bumper

2019-07-29T12:21:30Z

Added a picture of fog lamps and brackets mounted in a 2nd model front bumper

Bosanek: Some cleanup

2019-07-10T10:00:45Z

Some cleanup

@@ Line 486: / Line 486: @@
 *#** It appears that alternate catalogue P.N. for this fog lamp model is P.N. <font face="courier">088358</font>.
 *#*** Not stamped on the fog lamp itself, but stated in some catalogues as a "virtual" / formal catalogue Valeo number.
-*#** Renault uses the same lamp under its OEM P.N. <font face="courier">8200074008</font>.
+*#** The same (or very similar) lamp is used by:
 *# <font face="courier">35500-63J03</font> - found on many European Jimnys from mid-2000s;
 *#* This is probably the older "main" edition which was superseded by the current "main" edition;

@@ Line 484: / Line 484: @@
 *# <font face="courier">35500-63J04</font> - "main" / standard edition from Suzuki (with exceptions below);
 *#* The actual fog lamp product under this Suzuki catalogue number is made by Valeo, P.N. <font face="courier">89210094</font>.
 *#** Renault uses the same lamp under its OEM P.N. <font face="courier">8200074008</font>.
 *# <font face="courier">35500-63J03</font> - found on many European Jimnys from mid-2000s;

← Older revision		Revision as of 09:41, 6 December 2019
Line 577:		Line 577:
	[[File:Suzuki Jimny 3 - fog lamp wiring diagram - A01.png\|768px\|thumb\|left\|Crude DIY-made general diagram of front fog lamp wiring sections in a Jimny 3]]		[[File:Suzuki Jimny 3 - fog lamp wiring diagram - A01.png\|768px\|thumb\|left\|Crude DIY-made general diagram of front fog lamp wiring sections in a Jimny 3]]
	<br clear=all>		<br clear=all>
		+
		+	{{note\|More info on electrical connector types used in Jimnys is written in the article [[Electrical connector types\|'''Electrical connector types''']].}}

@@ Line 600: / Line 600: @@
-[[File:Suzuki Jimny 3 - fuse for front fog lamps - A01.jpg|400px|thumb|left|Main fuse box in a Jimny 3 type 5, with the existing 15A fuse for the front fog lamps marked with a reddish ellipse area.]]
+<gallery widths=500 heights=350 class=center caption="">
-[[File:Suzuki Jimny 3 - el. connector in the engine bay, front fog lamps - A01.jpg|450px|thumb|center|Unused "Cable connector 4" just behind the front left head lamp (in a LHD Jimny type 9, made in 2012)]]
+Suzuki Jimny 3 - fuse for front fog lamps - A01.jpg|Main fuse box in a Jimny 3 type 5, with the existing 15A fuse for the front fog lamps marked with a reddish ellipse area.
-<br clear=all>
+Suzuki Jimny 3 - el. connector in the engine bay, front fog lamps - A01.jpg|Unused "Cable connector 4" just behind the front left head lamp (in a LHD Jimny type 9, made in 2012

@@ Line 189: / Line 189: @@
 * Suffix "-000" should be omitted in some searches, and in some other catalogues it is listed with the suffix "-010".
 ** The difference between suffixes is probably in the languages in which the included paper instruction manual is written.
-* It is ''assumed'' (but not verified!) that the included fog lamp model is <font face="courier">35500-63J04</font>.
-* It is ''assumed'' (but not verified!) that this set contains exactly the same parts as the set <font face="courier">990E0-84A02-000</font>, with the exclusion of the pair of fog lamp mounting brackets.
-** This is because 3rd model front bumper has integrated front fog lamp brackets specifically for front fog lamps <font face="courier">35500-63J0x</font>;
+This set includes:
@@ Line 237: / Line 246: @@
 * This method can be much cheaper, especially if buying used items on a used items market or from a vehicle junkyard.
 * However, not each part (lamp, bracket, etc.) is mutually compatible nor compatible with each front bumper model.
 Known fog lamp models:
@@ Line 280: / Line 290: @@
 # Suzuki <font face="courier">36813-54G20</font>;
 #* Used at the "fog lamp to wiring" ("Cable connector 5") connection point in case of some particular setup combinations;
 # Suzuki <font face="courier">99000-990YZ-C13</font>;
 #* Used by DDiS Jimnys 3 type 4 only;
@@ Line 471: / Line 483: @@
 * The following fog lamp models appear to have exactly the same dimensions, shape, bulb, el. connector and mounting points to the brackets:
 *# <font face="courier">35500-63J04</font> - "main" / standard edition from Suzuki (with exceptions below);
-*#* It appears that the actual fog lamp product under this Suzuki catalogue number is made by Valeo, P.N. <font face="courier">89210094</font>.
+*#* The actual fog lamp product under this Suzuki catalogue number is made by Valeo, P.N. <font face="courier">89210094</font>.
 *# <font face="courier">35500-63J03</font> - found on many European Jimnys from mid-2000s;
 *#* This is probably the older "main" edition which was superseded by the current "main" edition;
 *# <font face="courier">35500-63J02</font> - meant for the African market;
 *# <font face="courier">35500-63J00</font> - used only in Jimnys 3 made by Santana in Spain;
@@ Line 620: / Line 635: @@
 Notes on <font face="courier">Cable connector 4</font>:
 * It appears that this connector is some specific type in Jimnys 3 type 1-5 (with 1st model front bumper) (needs more investigation).
-* This connector on Jimnys 3 type 6-12 (with 2nd and 3rd model front bumper) is actually the same male "bullet" type connector as <font face="courier">Cable connector '''5'''</font> in Jimnys 3 type 1-5!
+* This connector on Jimnys 3 type 6-12 (with 2nd and 3rd model front bumper) is actually the same male type connector as <font face="courier">Cable connector '''5'''</font> in Jimnys 3 type 1-5!
 ** See notes about <font face="courier">Cable connector 5</font> below for more details.
 Notes on <font face="courier">Wiring 4</font>:
-* This element krepresents the wiring harnesses:
+* This element represents the wiring harnesses:
 *# P.N. <font face="courier">'''?????-?????'''</font> for Jimnys 3 type 1-5,
 *# P.N. <font face="courier">36813-84A00</font> for Jimnys 3 type 6-8,
@@ Line 633: / Line 648: @@
 * Wiring 4 should easily be removable from a donor vehicle while the fog lamps are being removed.
 * Additional notes on harnesses <font face="courier">36813-84A00</font> and <font face="courier">36813-57M00</font>:
-** The connectors on these two harnesses should be the same.
+** The connectors on these two harnesses are the same.
 ** These two harnesses are compatible with fog lamp model <font face="courier">35500-63J0x</font>, which all Jimnys 3 type 6-12 use.
-** There could be that these two harnesses also use different mounting clips for attaching the harness to the vehicle body because Jimnys 6-8 and 9-12 use different from bumpers.
+** Harness <font face="courier">36813-84A00</font> can be used in Jimnys 3 type 9-12, but it will not be as Suzuki intended.
@@ Line 644: / Line 662: @@
 Notes on <font face="courier">Cable connector 5</font>:
 * There are two types <font face="courier">Cable connector 5</font> for front fog lamps in Jimnys 3.
-*# The first connector type is a "bullet" type connector, which was used in all Jimnys 3 type 1-5 (which originally came with 1st model front bumper, from 1998 to approx 2005).
+*# The first connector type was used in all Jimnys 3 type 1-5 (which originally came with 1st model front bumper, from 1998 to approx 2005).
 *#* This connector type is compatible only with front fog lamp model <font face="courier">35500-74F50</font>.
 *#** All other / newer fog lamp models which use H11 bulbs (including OEM fog lamps <font face="courier">35500-63J0'''X'''</font>) can be connected to the first / old type of <font face="courier">Cable connector 5</font> through a suitable connector adapter <font face="courier">36813-54G20</font>.
 *# The second / newer <font face="courier">Cable connector 5</font> type was used in all Jimnys 3 type 6-12 (which originally came with 2nd and 3rd model front bumper, from approx 2005 to 2018).
 *#* This newer <font face="courier">Cable connector 5</font> is actually a direct male connector for bulbs made according to H11 bulb standard.
@@ Line 653: / Line 672: @@
 *#*** However, a required el. connection could probably be made by cutting the <font face="courier">Cable connector 5</font> off and soldering the <font face="courier">Wiring 4</font> to the fog lamps directly.
-[[File:Suzuki Jimny 3 - OEM accessory 35500-74F50 - fog lamp, front, detail of el. connector to vehicle - A01.jpg|400px|thumb|left|Cable connector 5 as used by the fog lamp model 35500-74F50. This is the connector from the side of the fog lamp. Note that it happens to physically match Cable connector 4 from the picture above which taken from a much newer Jimny built in 2012, although they are not meant to be directly connected, and are positioned quite far apart.]]
+[[File:Suzuki Jimny 3 - OEM accessory 35500-74F50 - fog lamp, front, detail of el. connector to vehicle - A01.jpg|400px|thumb|left|Cable connector 5 as used by the fog lamp model 35500-74F50. This is the connector from the side of the fog lamp. Note that it happens to physically match Cable connector 4 from the picture above which taken from a much newer Jimny built in 2012, although they are not meant to be directly connected.]]
 <br clear=all>

@@ Line 527: / Line 527: @@
 ** Otherwise, there would be ugly gaps between the fog lamps and the bumper, which would make the setup look like an aftermarket improvisation.
 * 3rd model front bumper already comes with a pair of "blank" bezels attached in the place of fog lamps.
-** The "proper" bezels look exactly like the "blank" bezels, but only with a pre-cut hole for the fog lamps.
+** Left blank bezel P.N. is <font face="courier">71761-57M00-5PK</font> and right blank bezel P.N. is <font face="courier">71751-57M00-5PK</font>.
 ** Therefore, in theory, there is no need to buy "proper" bezels for retrofitting fog lamps to a 3rd model front bumper, as it should be (in theory) possible to carefully cut suitable holes for the fog lamps in the default "blank" bezels which are already present in the bumper, and achieve exactly the same look and finish.
 *** However, someone needs to try this in practice and report.

@@ Line 565: / Line 565: @@
 * The best case scenario which you could expect is to already have everything from the above crude diagram already installed from the factory, except <font face="courier">Fog lamps</font> + <font face="courier">Cable connector 5</font>, <font face="courier">Wiring 4</font> and <font face="courier">Switch</font>.
 * Therefore, you should first check for the presence of wires with unused el. connectors in the vehicle.
-*# First search for the unused <font face="courier">Cable connector 4</font> in the engine bay, just behind the head lamps (usually front left).
+*# First search for the unused <font face="courier">Cable connector 4</font> in the engine bay, just behind the head lamps.
-*#* If not found there, then search for it somewhere behind the front bumper (after removing the front inner wheel arch liners).
+*#* In Jimnys 3 type 1-5, there should be '''???????''' behind '''???????'''.
 *# Then check if the unused <font face="courier">Cable connector 3</font> for the console button / switch is present inside the console in the cabin (see the chapter about the installation of the console button / switch).
 * If you find both unused <font face="courier">Cable connector 4</font> and <font face="courier">Cable connector 3</font> (for the fog lamps and for the in-cabin switch) in your Jimny 3, consider yourself lucky!
@@ Line 577: / Line 580: @@
 **# <font face="courier">Wiring 4</font> to <font face="courier">Cable connector 4</font>;
 **# <font face="courier">Fog lamps</font> to <font face="courier">Wiring 4</font> via <font face="courier">Cable connectors 5</font>;
-**# Mount the fog lamps to the bumper and go on joyful rides ever since.
+**# Mount the fog lamps to the bumper and go on joyful rides on foggy mornings ever since.
 [[File:Suzuki Jimny 3 - fuse for front fog lamps - A01.jpg|400px|thumb|left|Main fuse box in a Jimny 3 type 5, with the existing 15A fuse for the front fog lamps marked with a reddish ellipse area.]]
-[[File:Suzuki Jimny 3 - el. connector in the engine bay, front fog lamps - A01.jpg|450px|thumb|center|Unused "Cable connector 4" just behind the front left head lamp (in a LHD Jimny made in 2012)]]
+[[File:Suzuki Jimny 3 - el. connector in the engine bay, front fog lamps - A01.jpg|450px|thumb|center|Unused "Cable connector 4" just behind the front left head lamp (in a LHD Jimny made type 9, made in 2012)]]
 <br clear=all>
@@ Line 620: / Line 623: @@
 Notes on <font face="courier">Wiring 4</font>:
-* It is a split dual wire harness which connects both fog lamps in parallel to <font face="courier">Cable connector 4</font> and is easily removed from a donor vehicle while the fog lamps are being removed.
+* This element krepresents the wiring harnesses:
-* This harness is represented by P.N. <font face="courier">36813-84A00</font> for Jimnys 3 type 6-8 and by P.N. <font face="courier">36813-57M00</font> for type 9-12.
+*# P.N. <font face="courier">'''?????-?????'''</font> for Jimnys 3 type 1-5,
-** The connectors on both of these harness models should be the same.
+*# P.N. <font face="courier">36813-84A00</font> for Jimnys 3 type 6-8,
-** These two harnesses are compatible with fog lamps model <font face="courier">35500-63J0x</font>, which all Jimnys 3 type 6-12 use.
+*#* It is a split dual wire harness which connects both fog lamps in parallel to a single <font face="courier">Cable connector 4</font>;
-** The reason for the existence of two different wiring harness P.N.s is probably because of different mounting clips for attaching the harness to the vehicle body and/or because of different wire lengths.
+*# P.N. <font face="courier">36813-57M00</font> for Jimnys 3 type 9-12.
 [[File:Suzuki Jimny 3 - OEM accessory 36813-57M00 - wiring harness, front fog lamp - A01.jpg|480px|thumb|left|Wiring harness 36813-57M00]]

← Older revision		Revision as of 12:21, 29 July 2019
Line 545:		Line 545:

	[[File:Suzuki Jimny 3 - OEM accessory 35500-74F50 + 35526-81A01 - fog lamp, front + bracket, in 1st model front bumper, rear view - A01.jpg\|800px\|thumb\|center\|Fog lamps 35500-74F50 with brackets 35526-81A01 mounted in 1st model front bumper, rear view]]		[[File:Suzuki Jimny 3 - OEM accessory 35500-74F50 + 35526-81A01 - fog lamp, front + bracket, in 1st model front bumper, rear view - A01.jpg\|800px\|thumb\|center\|Fog lamps 35500-74F50 with brackets 35526-81A01 mounted in 1st model front bumper, rear view]]
		+	<br clear=all>
		+
		+
		+	[[File:Suzuki Jimny 3 - OEM accessory 35500-63J04 + 35526-84A00 + 35566-84A00 - fog lamp, front + bracket, in 2nd model front bumper, rear view - A01.jpg\|800px\|thumb\|center\|Fog lamps 35500-63J0x with brackets 35526-84A00 and 35566-84A00 mounted in 2nd model front bumper, rear view]]
	<br clear=all>		<br clear=all>

@@ Line 202: / Line 202: @@
 * Fog lamp model <font face="courier">35500-74F50</font> and bracket model <font face="courier">35526-81A01</font> are available in a combo set P.N. <font face="courier">99000-990YZ-B01</font> (for the left side) and <font face="courier">99000-990YZ-B02</font> (for the right side).
 ** It is not known why there are two differently named sets (specifically for each side), since both the contained fog lamp and bracket models fit any side equally.
@@ Line 260: / Line 259: @@
 # Suzuki <font face="courier">99000-990YZ-B03</font> + <font face="courier">99000-990YZ-B04</font>
 #* (Left model + right model);
-# Possibly at least one more bezel model;
+#* It is assumed (but not verified!) that these bezels are for use with fog lamps Cibie <font face="courier">026719</font> in 1st model front bumper ''and/or'' with fog lamps Suzuki <font face="courier">35500-63J0x</font> in 1st model front bumper;
-#* For use with fog lamps Cibie <font face="courier">026719</font> in 1st model front bumper ''and/or'' with fog lamps Suzuki <font face="courier">35500-63J0x</font> in 1st model front bumper;
+# There could possibly exist one more bezel model for use with fog lamps Cibie <font face="courier">026719</font> in 1st model front bumper ''and/or'' with fog lamps Suzuki <font face="courier">35500-63J0x</font> in 1st model front bumper;
 # Suzuki <font face="courier">71761-57M10-5PK</font> + <font face="courier">71751-57M10-5PK</font>;
 #* (Left model + right model);
@@ Line 326: / Line 325: @@
 |Required<br>Seen on pictures<br>P.N. unknown
 |Required<br>Seen on pictures<br>P.N. unknown
-|Required<br>Seen on pictures<br>P.N. unknown
+|99000-990YZ-B03 ?
-|Required<br>Seen on pictures<br>P.N. unknown
+|99000-990YZ-B04 ?
 |Probably required<br>Probably 36813-54G20
 |"Improved"<br>(more complicated)<br>setup
@@ Line 334: / Line 333: @@
 |35566-81A30
 |35526-81A30
-|Probably required<br>P.N. unknown
+|99000-990YZ-B03 ?
-|Probably required<br>P.N. unknown
+|99000-990YZ-B04 ?
 |36813-54G20
 |"Universal<br>retrofit"<br>setup