View source for Manual or fixed front wheel hub heads

{{intro-notes}}


== Introduction ==


[[File:Vacuum operated wheel hub head on a wheel - B01.jpg|thumb|384px|left|Vacuum operated free-wheeling wheel hub head on a wheel]]

* Jimnys have pneumatically (vacuum) operated free-wheeling front wheel hub heads / caps.
* Pneumatic system is very convenient when it works, but it can be a nightmare when it fails.
<br clear=all>

[[File:Manually operated wheel hub head - A01.jpg|thumb|384px|left|Manually operated free-wheeling wheel hub head]]

* The purpose of this article is to provide you an alternative solution to repairing that system - replacing it altogether with manually operated free-wheeling front wheel hub heads.
* Even fixed front wheel hub heads can be installed (the procedure is almost the same) - this is also covered in this article.
<br clear=all>

{{note|The wiki article [[Vacuum hubs - checking and testing|'''"Vacuum hubs - checking and testing"''']] contains the following:<br>
* The general introduction about the purpose and operation of free-wheeling wheel hub heads;
* Description of operating systems for free-wheeling wheel hub heads;
* All the details about vacuum operated free-wheeling wheel hub heads;
* Related issues and repair solutions.}}

{{note|In order to properly understand this article, you should first properly understand the operating principles of Jimny's entire 4WD transmission system.<br> That topic is covered in a dedicated wiki article [[4WD transmission system operation|'''"4WD transmission system operation"''']].}}

{{note|Wheel hub heads / caps are usually just shortened in naming to "hubs", but a "hub" is actually an entire wheel hub assembly - the casing which contains the wheel bearing with its seals, the steering knuckle surround casing, the king pin bearings and (in the case of the Jimny) the pipes and passages which transport the air / vacuum through the wheel hub assembly to/from wheel hub heads.}}


== Solution with manually operated hub heads ==


=== Reasons and advantages ===


[[File:Vacuum and manual wheel hub head - A01.jpg|thumb|left|400px|Vacuum (top) and manual (bottom) free wheeling wheel hub head for a comparison]]

* Most Jimnys (especially those which are regularly used in all-terrain duty) will, inevitably, have problems with the vacuum system for front wheel hub heads.
* Diagnosis and repair, depending on the issue, can range from a quick detection and a simple/cheap fix, to a thorough and arduous investigation with expensive repairs.


* However, there is luckily an alternative solution - to completely discard the vacuum system and vacuum front wheel hub heads, and install manually operated free wheeling front wheel hub heads (like in Samurais and other classic 4WD vehicles) or even fixed hub heads.
* This will eliminate the entire vacuum system, and with it all the risks and issues which it imposes.
* Manually operated free wheel wheel hub heads generally have the lowest risk of failures, as there is by far the least amount of components which can fail.
* The modification is relatively simple to perform, with required parts widely available on the second hand market and/or in the aftermarket.
<br clear=all>


This solution is worth considering in the following scenarios:
# If you are tired with chasing faults in your vacuum system for front wheel hub heads;
# If the determined repair of the fault is too expensive;
# If you just want to preventively minimize the risk of a failure;


* Also, manually operated front wheel hub heads indirectly allow the use of the "2WD-L" transmission mode, which Suzuki has not enabled by default in any Jimny.
* Read the wiki article [[2WD-L transmission mode|'''"2WD-L transmission mode"''']] for all the details.


=== Disadvantages ===


* The operator has to exit the vehicle and manually switch both hub heads whenever their (dis)engagement is desired.
* As most manual free wheeling hub heads have no anti-tamper mechanisms, a malicious person can easily (dis)engage a hub head while the vehicle is parked (easily remedied by the driver when detected, but can cause confusion while driving in the meantime).
* If water enters into a manual free wheeling hub head, it can freeze the manual (un)locking spring mechanism in the hub head during frigid weather. If this happens while the hub head is disengaged, it can prevent the vehicle from using 4WD transmission when it is needed the most.


=== Practical tips when using manual wheel hub heads ===


* It is NOT strictly required to engage/disengage the wheel hub heads every time when switching between <font face="courier">2WD<->4WD</font> transmission modes.
* In other words, it is completely fine to leave the wheel hub heads engaged during 2WD transmission mode. The vehicle will just use a bit more fuel (since more metal is spinning) and that metal will naturally wear more compared to when being disconnected and resting idle.
* This means that you can have the hub heads engaged all the time during the day(s) when you expect to shift between <font face="courier">2WD<->4WD</font> transmission modes often. This will save you many exists from the vehicle.


* If you suspect upcoming freezing weather conditions (for example for the next morning after parking the car in the evening), it might be a good precautionary measure to leave the hub heads engaged over night on the parking lot, in case that the (un)locking mechanism in them freezes. Better to have them frozen ON than frozen OFF!


* Develop a habit to occasionally check the (dis)engagement status of your manual hub heads, in case that someone has fiddled with them on a parking lot!


== Solution with fixed wheel hub heads ==


[[File:Fixed wheel hub head on a wheel - A01.jpg|thumb|left|348px|Fixed wheel hub head on a wheel]]

* It is also possible to install fixed hub heads.
* Fixed hub heads are usually much smaller than any other type of hub head.
* Their availability on the aftermarket for Jimnys is much lower.
* One possible source of obtaining fixed hub heads would be from a vehicle junkyard which has a dead "el cheapo" 2WD-only Jimny (quite rare, produced from 1998 to 2001).
* The other possible source would be from a SJ413 (Samurai) and from Vitara Mk1 (and possibly from Vitara Mk2 as well?), but it is not known if some additional spacers are required.


* The procedure for performing the conversion to fixed hub heads is exactly the same as the procedure for the conversion to manually operated wheel hub heads.
* Therefore, this article can be fully utilized for that type of conversion as well.
* The only difference in the end will be that you will never be able to disengage the front wheels from the drive line.
* This is the same operational effect as when having manually operated wheel hub heads engaged all the time.
<br clear=all>


The advantages of fixed hub heads vs. manual hub heads:
* Nobody can maliciously disengage them on a parking lot;
* They are theoretically more durable for extremely heavy-duty operation;
* Their much smaller size means that they protrude much less from the wheel to the sides, minimizing chances of hitting something and getting damaged in extremely heavy-duty all-terrain use.


=== Modifying original vacuum wheel hub heads to fixed hub heads ===


* There is an alternative unorthodox solution to modify Jimny's original vacuum-operated front wheel hub heads so that they become fixed (always engaged).
* The advantage of this solution is that no new (replacement) fixed hub heads are needed.
* It can be accomplished in a few ways.
* That topic is thoroughly discussed in [https://www.bigjimny.com/index.php/forum?view=topic&catid=7&id=55862 this BigJimny forum topic].


* After the vacuum hub heads are converted to fixed hub heads, the part 2 (and possibly part 3 as well, depending on your choices below) of the conversion process in the next chapter still need(s) to be performed.


== Converting from vacuum to manually operated front wheel hub heads ==


=== Introduction ===


Although this article appears enormous in length, don't be overwhelmed - it is really rather simple, but it has been "broken down" to each phase and option and written in detail - hence the length.


[[File:Manual or fixed front wheel hubs on a Jimny - modification diagram - A01.png|thumb|left|656px|The entire modification procedure in a neat overview diagram]]

This modification is performed in three parts:
# Removing the old vacuum operated hub heads and installing manually operated hub heads (or fixed hub heads);
# Blocking or removing the vacuum system (valves, pipes);
# Fooling the 4WD controller into thinking that the vacuum system still works as normal, or removing the 4WD controller altogether.


* All three parts of the modification are rather simple to perform.
* The first two parts are quite "straightforward".
* The choices in the third part differ for vehicles with manually operated transfer boxes and for vehicles with electrically operated transfer boxes.
* Reason: While the 4WD controller can be completely discarded in the older (lever-operated) transmission system, it has to remain fully working in the newer (button-operated) transmission system.


{{note|The wiki article [[4WD transmission system operation|'''"4WD transmission system operation"''']] explains in detail how Jimny's 4WD transmission system operates.<br>It is vital in understanding why some steps in this procedure are performed.}}
<br clear=all>


=== Part 1: Installing fixed or manually operated hub heads ===


==== Introduction ====


* This phase of the conversion is the same for all Jimnys.
* There are four solutions on how to achieve it.


==== Solution 1a - old manual hub heads from a Samurai or a Vitara ====


===== Introduction =====


This solution is less expensive of the two solutions with manually operated free wheeling hub heads, but involves more "fiddling" around.


Required parts: 
* A pair of manually operated, second hand hub heads from a Suzuki SJ413 (Samurai) or from a Suzuki Vitara (Escudo / Sidekick / GeoTracker) Mk1.
* The cones from the SJ / Vitara hub head bolts;
* Since the hub heads from earlier Suzuki vehicles do not fit directly on a Jimny, a pair of special spacers/adapters (with suitable bolts), which sit between these hub heads and the wheel hub assembly, is also required.
** Reason: The vacuum sealing ring on the Jimny hub nut stops the SJ hubs from fitting. You could simply undo the hub nut and grind off the sealing ring. However, for this you will need a special tool to undo the hub nut.


{{note|There are numerous versions and editions of Suzuki SJ413s, Samurais and Vitaras in existence.<br>Only some of them had manual hub heads as a factory fitment, and Suzuki used hub heads from several OEMs.<br>With any second-hand equipment, checking its condition beforehand is always vital!}}


[[File:Manual wheel hub head from SJ installation - figure 01 - SJ manual hub heads.png|thumb|left|480px|Figure 01 - SJ manual hub heads]]
<br clear=all>

[[File:Manual wheel hub head from SJ installation - figure 02 - cone washers from SJ hub head bolts.png|thumb|left|480px|Figure 02 - The cone washers from SJ hub head bolts]]
<br clear=all>


[[File:Manual wheel hub head from SJ installation - figure 03 - wheel hub head spacers from BigJimny.png|thumb|left|480px|Figure 03 - wheel hub head spacers]]
* Browse the shops like BigJimny, JimnyBits, Bits4Vits, etc. for suitable spacers/adapters (or for the special tool if you are a "headlong" type!).
* If you decide for the spacer rings, BigJimny sells a kit to sort out this problem.
** In the kit you get two spacer rings and 12 Hex cap bolts.
** The kit includes replacement bolts as the Jimny and SJ bolts are too long and too short respectively.


* This picture shows the BigJimny rings (the photo is of the prototype rings painted blue, the shop versions are properly plated):
<br clear=all>


[[File:Manual wheel hub head from SJ installation - figure 04 - SJ and Jimny hub head bolts.png|thumb|left|480px|Figure 04 - SJ and Jimny bolts]]
<br clear=all>


===== Installation guide =====


The replacement procedure is really simple and straightforward.


[[File:Manual wheel hub head from SJ installation - figure 05 - E10 Torx socket.png|thumb|left|320px|Figure 05 - E10 "Torx" socket]]
* First remove both Jimny vacuum hub heads using an E10 Torx socket.
<br clear=all>


[[File:Manual wheel hub head from SJ installation - figure 06 - hub head spacer ring coated with sealant.png|thumb|left|480px|Figure 06 - spacer ring coated with sealant]]
* Coat the spacer ring with a thin layer of sealant to keep the water out.
<br clear=all>



[[File:Manual wheel hub head from SJ installation - figure 07 - SJ cone washers on new bolts.png|thumb|left|480px|Figure 07 - SJ cone washers on the new bolts]]
* Slide the cones from the SJ hubs onto the new bolts.
<br clear=all>


[[File:Manual wheel hub head from SJ installation - figure 08 - bolt coated with thread locker.png|thumb|left|480px|Figure 08 - Coated bolt with thread locker]]
* Now coat the bolts with a thin layer of thread locker.
<br clear=all>


[[File:Manual wheel hub head from SJ installation - figure 09 - SJ hub head front plate removal.png|thumb|left|480px|Figure 09 - removing the SJ hub heads's front plate]]
* Mate the hub head to the wheel hub and screw the bolts in by finger as far as possible.
* You may find that the front of the hub head prevents you from getting at the new bolts.
* In this case, set the hub head to FREE position and undo the hub head's front plate.
<br clear=all>


[[File:Manual wheel hub head from SJ installation - figure 10 - SJ hub head bolt tightening.png|thumb|left|480px|Figure 10 - tightening the bolts]]
* Now you should be able to tighten the bolts.
* Tighten them sequentially in a "star" pattern, like when mounting a wheel.
* Go around the hub a couple of times to tighten the bolts fully.
<br clear=all>


[[File:Manual wheel hub head from SJ installation - figure 11 - SJ hub head successfully installed.png|thumb|left|480px|Figure 11 - successfully installed manual SJ 413 hub head]]
* Now refit the SJ hub head front plate and admire the finished installation.
<br clear=all>


==== Solution 1b - aftermarket tailor-made Jimny manual hub heads ====


This solution is more expensive of the two solutions with manually operated free wheeling hub heads, but is the most elegant of all.

Required parts:
* A pair of aftermarket-made manually operated hub heads which are specifically designed for Jimnys.
* These are a direct "bolt-on" replacement - no spacers/adapters needed!
** The described procedure from solution 1a can be generally applied here as well, except that it is much simpler here - no issues with any bolts.

{{note|The quality of aftermarket manual hub heads for Jimnys varies depending on a brand. There are even some no-name models around. You get what you pay for!}} 


==== Solution 1c - fixed hub heads ====


This solution should be the most robust, but the parts might be hard to find.


Required parts:
* A pair of compatible fixed hubs for Jimnys.
* Depending on their source, you might need some spacers/adapters for them.

{{note|This solution needs additional info from someone who has done this.}}


==== Solution 1d - converting existing vacuum hub heads into fixed hub heads ====


* There are no additional parts required for this solution.
* Therefore, it is the cheapest of all solutions.
* It just needs some ingenuity and mechanical (or welding) skills in order to convert the hubs.

{{note|Beware that, in general case, the strength / robustness of modified (fixated) vacuum hub heads can never match the strength of true fixed hub heads, no matter which method to modify them was utilized.}}


==== Required tools ====


Required tools in any case are:
* An E10 "torx" socket is required to demount the vacuum hub head bolts from the wheel hub assembly.
* Required socket for mounting the new hub heads on the wheel hub assembly depends on what bolt type the new hub heads use.
* If you happen to need to disassemble the replacement second-hand hub heads in order to clean and re-grease them, you will then need additional tools and a suitable grease for that job.
* For solution 1d, a welding machine or some other mechanical tools might be required.


==== Practical notes ====


* Once you assemble all these parts and tools, replacing the hub heads is a rather simple job to do (unless a bolt is stuck :).
* It can be done even on a field, as there's usually no need to lift the vehicle or to use any special equipment.


* It has also been reported that manual or fixed hub heads from a Suzuki SJ410 / SJ413 / Samurai can allegedly be installed on a Jimny without any spacers.
* The prerequisite is that Jimny's "vacuum tight" hub nut is removed and a corresponding hub nut from the donor SJxxx vehicle is installed in its place.
* This also removes the need to use the special Jimny hub nut unlocking tool when changing a wheel bearing afterwards.


=== Part 2: Blocking or removing the vacuum system (valves, pipes) ===


==== Reasons ====


* After the first part of the conversion is complete, you will either have permanently locked wheel hub heads (in the case of fixed hub heads) or you will be able to manually (dis)engage the front wheels from/to the front drive line at will (in the case of manual hub heads).
* Whatever the case, the vacuum system will be left "hanging in the air", doing its job in the void (literally) - trying to achieve vacuum in vain.
* This means that the 4WD controller will not function correctly, because it will never receive the signal about successful vacuum formation from the vacuum system.


===== Situation with manually (lever) shifted transfer boxes =====


* It will still be possible to shift the transfer box into from 2WD into 4WD-H transmission mode just fine (since the operator is doing it personally with a mechanical lever).
* Therefore, <font face="courier">2WD<->4WD-H</font> (dis)engagement will work just fine. Just don't forget to manually engage the front wheel hub heads as well!
* However, the 4WD controller will be aware that something is wrong with the vacuum system, so the green 4WD light will constantly flash while 4WD mode is active.
* It will also be possible to further shift from 4WD-H to 4WD-L mode and back, as the driver is doing it personally, directly with a mechanical lever.


* For non-ABS equipped vehicles, the flashing green 4WD light is just a non-important visual inconvenience, which can be remedied (read further below).


* For ABS-equipped vehicles, the operation of the ABS controller probably differs whether the vehicle is formally in 2WD or in 4WD mode.
* In this case, it might be of vital importance to remedy the operation of the 4WD controller (and with it the green 4WD light).


===== Situation with electrically (button) shifted transfer boxes =====


* It will NOT be possible to shift between <font face="courier">2WD<->4WD-H</font> transmission modes, as the 4WD controller electromagnetically operates the (dis)engagement mechanisms in the transfer box after your push-button invocation.
* The controller will refuse to perform the shift, because it detects a leak in the vacuum system (manual and fixed hub heads are not air-tight, and that's where the leak is).
* Consequently, it will not be possible to shift into 4WD-L mode, as it prerequisites proper engagement of 4WD-H mode.
* The remedy requires the fooling of the 4WD controller into thinking that the vacuum system operates just fine.
* When that is accomplished, the 4WD controller will work as before, including the operation of the green 4WD light on the instrument panel, and also notifying the ABS system whenever a <font face="courier">2WD<->4WD-H</font> change is made.


==== Possible solutions ====


* In order to remedy this situation, this part of the conversion makes the conditions to fool the 4WD controller into thinking that the vacuum system is still operating normally (although the operation of the vacuum system is no longer needed in practice).
* This means that (in the end) even the green 4WD light on the instrument panel will function correctly, but it will have no meaning regarding the (dis)engagement of the front wheel hub heads.
* The green 4WD light will only indicate whether the transfer box has engaged the front drive line or not.
* The goal can be accomplished in two methods, and either method can be applied to any Jimny (petrol or diesel, with lever-operated or button-operated 4WD transmission system).


* Solution 2a is to block the pipes in the vacuum system, forcing the formation of the vacuum.
* Solution 2b is to remove the entire vacuum system from the vehicle, and then to modify the wiring to simulate the return signals from the vacuum system to the 4WD controller.


==== Solution 2a - blocking the vacuum system ====


* Solution 2a is a simpler solution - just to block the vacuum pipes, so there will be no leaks in the vacuum system.


* After blocking the pipes, the vacuum system will report a successful vacuum formation every time when its operation is invoked, fooling the 4WD controller into thinking that everything is normal.


{{note|By performing solution 2a, you have automatically accomplished part 3 of the conversion (solution 3a - fooling the 4WD controller) and your work is done!}}


The vacuum system can simply be blocked (for example with raw rubber or even better with some protective caps) at any of these two points:
# At the end of the pipes where they enter the wheel hub assemblies - disconnecting the pipes from the wheel hub assemblies and then blocking both the pipes and the hub connections;
# At the valves in the engine bey - disconnecting the pipes from the valves and then blocking both the pipes and the valves.


===== Disadvantages and constraints =====


* The first disadvantage of this solution is that the vacuum valves and switches will still operate (in vain) every time when <font face="courier">2WD<->4WD</font> mode is changed.
* It's not a major technical issue, but some people really hate having an ''Appendix'' in their car / system. It's more a matter of principle.


* This solution is applicable only if the vacuum system is working fine at the moment, or if it has a vacuum leak somewhere between the vacuum check valve and the wheel hub heads.
* If some of the vacuum valves or switches is faulty, or if the vacuum source itself is faulty, or if some electrics are faulty etc., then blocking the system will have no effect, as it will not contribute to the formation of the vacuum in the system.
* In this case, the malfunction has to be remedied first in order for this solution to be applied. It may be better to choose the other solution instead (read below).
* Even if the vacuum system is working fine at the moment and is successfully blocked, a valve / switch / electrics / vacuum generator failure in the future can still render the system faulty without vacuum - preventing the 4WD controller from working properly.



==== Solution 2b - discarding the entire vacuum system ====


* This is a slightly more complicated solution.
* However, it is much more error-proof in the long term, because all the vacuum system elements (along with their operational risks) will be eliminated.
* If you remove the vacuum system, it will be much more complex to "return" back to vacuum-operated wheel hub heads later in the future (if you or a future vehicle buyer wants to do it).


{{warning|You perform this solution '''at your own risk'''!<br>In theory, the 4WD computer should sustain NO damage from having the wires between it and the vacuum valves and switches disconnected.<br>But like in any modification written in this wiki, there are no guarantees!}}


To remove the vacuum system, just demount the following:
* The vacuum tank under the vehicle (exists in petrol models only!);
* Valves marked VSV1 and VSV2 in Suzuki's technical documentation;
* Vacuum metering valve;
* The check valve;
* All vacuum pipes connecting the engine, the valves, the tank and the wheel hub assemblies;
* Don't forget to block the vacuum connection points on the engine itself and on the wheel hub assemblies!
* Isolate the leftover electrical wires, or, if you are really meticulous, remove all the electrical wires which were connected to the valves.


{{note|
* It is advised to first simulate the removal of the vacuum system elements by disconnecting all the wires from all vacuum valves, switches, tanks etc. and by blocking the vacuum pipe coming from the engine.
* Then perform solution 3a or 3b below.
* If it is all right in the end, then truly and physically remove all vacuum system elements.
* This way you can easily return everything back if the simulation test shows that the end results of the modification are not behaving as planned.}}


=== Part 3: Fooling or removing the 4WD controller ===


==== Introduction ====


* This part of the conversion is performed only after removing the vacuum system (solution 2b) in part 2 of the conversion.
* In other words - if you decided to block the vacuum system (solution 2a) in part 2 of the conversion process, then you do not need to do anything in part 3 - your conversion is already done!
* The available choices in this part depend on whether the Jimny has an older lever-operated transfer box or a newer button-operated transfer box.


==== Solution 3a - fooling the 4WD controller ====


* This is one of two possible solutions for Jimnys with older lever-operated transfer box.
* This is the only possible solution for Jimnys with newer button-operated transfer box, because the 4WD controller has to remain fully working in the vehicle.


* The solution is to fool the 4WD controller that the (now non-existent) vacuum system is still operating just fine.
* The goal is to simulate a return signal from the vacuum system to the 4WD controller (the signal which informs the controller if the vacuum has formed when the operation of the vacuum system is invoked).
* This is accomplished by permanently short-circuiting the electrical connector which was connected into the vacuum metering valve.
* Alternatively, you can follow the wires from that connector directly into the 4WD controller, and make a short-circuit directly at 4WD controller's pins.
* This way you can discard all that wiring between the 4WD controller and the former vacuum metering device.
* Reason for the short circuit: This valve used to short-circuit this connector whenever it sensed a successful vacuum formation. By permanently shorting the wires, the 4WD controller will always believe that the vacuum system is working fine. A permanent short circuit condition should not harm it (theoretically).


==== Solution 3b - removing the 4WD controller ==== 


* This solution is possible only if the Jimny has an older lever-operated transfer box.
* Do not perform this solution on newer Jimnys with a newer button-operated transfer box, as the 4WD controller is required to operate the transfer box itself!


* Since the 4WD controller is now left without anything to control (except the 4WD light on the instrument panel and informing the ABS controller), it can be discarded as well.
* This will "free" the vehicle of all electronic / smart / modern / vulnerable elements of the 4WD transmission system. It will be as classic as a Willys Jeep.
* The removal of the 4WD controller will abolish the operation of the green 4WD light on the instrument panel, but it can be brought back into regular service by connecting it directly to a switch in the transfer box.


[[File:4WD_module.jpg|left|thumb|640px|Suzuki Jimny 4WD controller module (<'05)]]

* Here is the actual 4WD controller.
<br clear=all>


[[File:4WD_module_location.jpg|left|thumb|640px|4WD module location (in LHD vehicle)]]

* You first need to locate the module.
* It is placed just above the speaker on the driver's side.
<br clear=all>


* The coupler is easily removed by hand, and the module itself is held in place by a single M10 nut (located on top of the module).
* Unplugging the coupler completely disables the vacuum system, as well as the green 4WD light.
* If you now start the engine and move the 4WD lever to 4H or 4L position, the transfer box will still engage the propeller shaft and/or the low range gear as usual, but you will have no indication of that on your instrument panel.


[[File:4WD_module_coupler_hack.jpg|left|thumb|640px|A coupler setup with the green 4WD light re-enabled after 4WD module removal]]

* To re-enable the green 4WD light on the instrument panel, you need to connect the blue/black cable (it comes from the switch on the transmission box) in the coupler with the blue one (it goes to the green 4WD light and the ABS module if equipped).
* Just connect the aforementioned cables with a piece of wire and do not forget to secure and insulate the connection.
<br clear=all>


===== Disclaimer =====


* This chapter about removing the 4WD controller is provided '''AS IS'''.
* You modify your car at your own risk!
* Perhaps this is illegal in your country / area / religion / wife's house rules / whatever.


* The main issue is that the operation of the anti-lock braking system (in theory) differs in 2WD and 4WD modes.
* Therefore, without a normally functioning 4WD controller, the ABS system will not be aware that the vehicle is in 4WD mode.
* In a worst case, improper operation of the anti-lock braking system can lead to life-threatening consequences!


* I have tested the removal of the 4WD controller on a non-ABS vehicle and had no errors or malfunctions originating from this modification.
* However, I would highly advise testing an ABS-equipped vehicle functioning in a secure environment.
* THEORETICALLY, if you have an ABS-equipped vehicle, and you unplug the module and connect blue/black and blue cables, the ABS controller should receive exactly the same reading as before (it's the same blue cable, it gets the same nominal 13V current).
* I just have no way to test it.

{{Edited}}
[[Category:Modifications]]
[[Category:Howto]]
[[Category:Drivechain]]