<?xml version="1.0"?>
<feed xmlns="http://www.w3.org/2005/Atom" xml:lang="en-GB">
	<id>https://www.bigjimny.com/mediawiki/api.php?action=feedcontributions&amp;feedformat=atom&amp;user=Leftcase</id>
	<title>BigJimny Wiki - User contributions [en-gb]</title>
	<link rel="self" type="application/atom+xml" href="https://www.bigjimny.com/mediawiki/api.php?action=feedcontributions&amp;feedformat=atom&amp;user=Leftcase"/>
	<link rel="alternate" type="text/html" href="https://www.bigjimny.com/mediawiki/index.php/Special:Contributions/Leftcase"/>
	<updated>2026-11-17T15:42:07Z</updated>
	<subtitle>User contributions</subtitle>
	<generator>MediaWiki 1.46.2</generator>
	<entry>
		<id>https://www.bigjimny.com/mediawiki/index.php?title=Clutch_replacement&amp;diff=681</id>
		<title>Clutch replacement</title>
		<link rel="alternate" type="text/html" href="https://www.bigjimny.com/mediawiki/index.php?title=Clutch_replacement&amp;diff=681"/>
		<updated>2016-06-06T20:06:09Z</updated>

		<summary type="html">&lt;p&gt;Leftcase: &lt;/p&gt;
&lt;hr /&gt;
&lt;div&gt;{{note|Use the &amp;quot;Print as PDF&amp;quot; tab above to print}}&lt;br /&gt;
= A guide to changing the clutch. =&lt;br /&gt;
&lt;br /&gt;
It is inevitable that at some point you will have to face changing the clutch. It dips in and out of the mud on a regular basis as the bell-housing is not sealed. Eventually the clutch thrust bearing will start rattling and the action will become stiff and heavy.&lt;br /&gt;
Changing the clutch on a Jimny seems to be not for the faint hearted. It’s a very physical task and it is not pleasant struggling with the gearbox under the car, it is a very tight fit in the transmission tunnel.&lt;br /&gt;
&lt;br /&gt;
No special tools are required, but a good toolkit is needed. You will need extension bars for a socket set as some of the bolts are well hidden and difficult to access.&lt;br /&gt;
A breaker bar is also needed as some bolts are very tight.&lt;br /&gt;
&lt;br /&gt;
If this hasn’t put you off then its time to start work. It goes without saying that you should jet-wash the underside of the car if possible to remove as much of the muck before it drops on you!&lt;br /&gt;
There are two ways of changing the clutch, one is to take the engine and gearbox out and the other is to drop the gearbox off. The Suzuki factory manual suggests the gearbox dropping method so that is the way I have gone.&lt;br /&gt;
&lt;br /&gt;
The factory manual suggests it is not necessary to remove the transfer box, but I have removed it as you will need all the space you can get, I thoroughly recommend that you also remove the transfer box.&lt;br /&gt;
&lt;br /&gt;
If you have the luxury of a bit of time then spray the visible bolts with WD40 a day or so before. In particular you should try and spray the bolts holding the exhaust front section and the bolts around the gearbox housing as these are difficult.&lt;br /&gt;
&lt;br /&gt;
== Removing Interior Items ==&lt;br /&gt;
&lt;br /&gt;
Starting inside the car it is necessary to remove both the gear lever and the transfer box lever.&lt;br /&gt;
&lt;br /&gt;
To remove the gearbox lever you have to remove the centre console. This is held on by four screws on the side at the front and back.&lt;br /&gt;
&lt;br /&gt;
=== Centre Console ===&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 1. Removing the Centre Console.png|thumb|left|250px|Figure 1. Removing the Centre Console]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
The console then lifts out. Mine was more of a problem as I have a switch panel fitted so I then needed to remove the gearlever before the console would come completely away, but this has to be done at some point anyway. Pull the gaiter away to reveal the three bolt heads around the base of the gearlever, undo the bolts and carefully lift out the gearstick, note that there is a small spring and a cup that should not be lost!&lt;br /&gt;
&lt;br /&gt;
=== Gear levers ===&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 2. Removing the Gearlever.png|thumb|left|250px|Figure 2. Removing the Gearlever]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
=== Lower Gaiter ===&lt;br /&gt;
&lt;br /&gt;
With the console removed you will then see a frame that holds in a second gaiter. Simply undo the bolts and lift the frame clear.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 3. Removing the lower Gaiter.png|thumb|left|250px|Figure 3. Removing the lower Gaiter]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
=== Transfer Lever ===&lt;br /&gt;
&lt;br /&gt;
If you are removing the Transfer Box then you need to remove the gaiter etc. around the Transfer Box Level. First locate the small screw at the rear of the transfer knob and remove it.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 4. Removing the Transfer Lever Knob.png|thumb|left|250px|Figure 4. Removing the Transfer Lever Knob]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Unscrew the frame around the gaiter and pull the frame and gaiter clear.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 5. Removing the Transfer Level Gaiter.png|thumb|left|250px|Figure 5. Removing the Transfer Level Gaiter]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
== Draining the Oil ==&lt;br /&gt;
&lt;br /&gt;
Move outside the car and disconnect the negative cable at battery.&lt;br /&gt;
&lt;br /&gt;
Now drain the oil from the gearbox and transfer box, if you are not doing any work on the transfer box then it is not strictly necessary to drain the oil providing you keep it upright to stop the oil coming out of the lever hole.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 6. Gearbox Drain Plugs.png|thumb|left|250px|Figure 6. Gearbox Drain Plugs]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
On my Jimny the drain plugs are square and therefore the square end of a 3/8 socket driver fits. Always undo the filler plug first because if the filler is stuck you do not want to drain the oil and not be able to fill it again. The gearbox filler is hidden up the side of the gearbox and lack of space is a problem&lt;br /&gt;
&lt;br /&gt;
== Removing Front Exhaust Section ==&lt;br /&gt;
&lt;br /&gt;
=== Exhaust ===&lt;br /&gt;
&lt;br /&gt;
On the Transfer Box disconnect the 4WD switch wire at coupler and unclamp harness. Then disconnect the speed sensor coupler.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 7. Transfer Box Fillers and Connectors.png|thumb|left|250px|Figure 7. Transfer Box Fillers and Connectors]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Now remove the front section of the exhaust pipe. This is held in place by pairs of springs with bolts inside. Due to the heat and stress the front bolts were really, really difficult to move. So much so I think there is real possibility of shearing them on some cars. There is a pair at the front and a pair at the back.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 8. Exhaust Bolts.png|thumb|left|250px|Figure 8. Exhaust Bolts]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
=== Lambda Sensor ===&lt;br /&gt;
&lt;br /&gt;
Do not lift the exhaust of the rubber hangers yet. There is a Lambda sensor connected to the top of the catalytic converter.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 9. Lambda Sensor on Converter.png|thumb|left|250px|Figure 9. Lambda Sensor on Converter]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
This needs to be disconnected. The Suzuki manual shows the sensor being unscrewed from the top of the converter. However, the sensor has been subject to red hot heat, water and mud, therefore mine was firmly rusted in. Instead I followed the wiring back up to behind the engine. Just behind the head on the passenger side is a set of connectors, unbolt the connector mounting bracket and prise the Lambda connector apart (this is very stiff as well!).&lt;br /&gt;
&lt;br /&gt;
[[File:Lambda Sensor Connector Behind Here.png|thumb|left|250px|Lambda Sensor Connector Behind Here]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
With the Lambda sensor disconnected you can pull the front exhaust section off the rubber mounts.&lt;br /&gt;
&lt;br /&gt;
== Removing the Prop shafts, Transfer Box &amp;amp; Gearbox Remote Mechanism ==&lt;br /&gt;
&lt;br /&gt;
=== Prop shafts ===&lt;br /&gt;
&lt;br /&gt;
Now remove the propshafts. On each shaft paint some marks so they can be rebolted to the flanges in the correct position when you are re-building it. Paint all the flanges and also mark the sliding joint in the front propshaft. Remove the FRONT propshaft FIRST, followed by the Gearbox/Transfer box shaft SECOND. Where possible do the REAR propshaft LAST. Why! – because all the propshaft bolts are quite tight and therefore you need to hold the propshafts in place whilst you try to undo the bolts. As the front hubs are vacuum operated there is no easy way to lock the props if you have disconnected the rear first. With the rear prop still on the rear wheels keep the system locked. I found out this trick the hard way.&lt;br /&gt;
&lt;br /&gt;
[[File:Mark the Propshaft.png|thumb|left|250px|Mark the Propshaft]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
=== Transfer Box ===&lt;br /&gt;
&lt;br /&gt;
Now undo the 3 large mounting nuts on the transfer box mount and the 4 bolts on the mounting flange. Now the transfer box should lift down.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 10. Transfer mounts.png|thumb|left|250px|Figure 10. Transfer mounts]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 11. Transfer Mounts.png|thumb|left|250px|Figure 11. Transfer Mounts]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
=== Gearbox Remote Mechanism ===&lt;br /&gt;
&lt;br /&gt;
Now for the complex bit. The Jimny has a remote gearbox mechanism bolted onto the rear of the gearbox and this needs to be removed. It’s probably easier to see the part after it has been removed as it is clearer what you are trying to achieve. Note this is the top view, you will normally be underneath!&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 12. Gearbox Remote Mechanism.png|thumb|left|250px|Figure 12. Gearbox Remote Mechanism]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Remove gear shift control joint bolt and extension rod bolt.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 13. Remote Mechanism in place.png|thumb|left|250px|Figure 13. Remote Mechanism in place]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
== Removing the Engine Mounting Bolts, Starter Motor and Clutch Cable ==&lt;br /&gt;
&lt;br /&gt;
=== Engine Mounting ===&lt;br /&gt;
&lt;br /&gt;
Remove the Engine Rear Mounting bolts (Three of them, one either side and one in the rubber bit). This is the mount under the gearbox that rests on the chassis crossmember.&lt;br /&gt;
&lt;br /&gt;
Using a long socket extension, reach into the remote mechanism and undo the 4 bolts that connect it to the gearbox. These are hard to reach.&lt;br /&gt;
&lt;br /&gt;
The entire mechanism should then be removeable complete with the mounts. Also unbolt all the other metal bits (including the exhaust mounting rubber) from the rear cross member as you will need to squeeze the Gearbox out later on.&lt;br /&gt;
&lt;br /&gt;
=== Reversing Switch ===&lt;br /&gt;
&lt;br /&gt;
Now remove the reversing light switch. This is on top of the gearbox towards the front and was more accessible from under the bonnet by reaching down the back of the engine on the passenger side (UK). Tie it up out of the way.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 14. Gearbox Reverse Switch.png|thumb|left|250px|Figure 14. Gearbox Reverse Switch]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
=== Starter Motor ===&lt;br /&gt;
&lt;br /&gt;
Now for the next difficult task, removing the starter motor. Clearly Suzuki never considered that a starter motor may go wrong and need replacing as it is in one of the most in-accessible places. First of all check that you have disconnected the battery. Laying under the car reach up the drivers side of the engine and unbolt the two bolts holding the motor in place and easy it back. There is no need to remove it completely and no need to undo all the cables attached to in.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 15. Starter Motor (from underneath car).png|thumb|left|250px|Figure 15. Starter Motor (from underneath car)]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
=== Clutch Cable ===&lt;br /&gt;
&lt;br /&gt;
We are nearly there now. Remove plastic clutch housing cap and prise the end of the clutch cable from clutch release fork. Then undo the two bolts holding the clutch cable to the transmission and withdraw the clutch cable assembly. Also remove the small tin-plate on the bottom front of the clutch housing held on by a pair of small 10mm bolts.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 16. Clutch cable (unhooked).png|thumb|left|250px|Figure 16. Clutch cable (unhooked)]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
== Seperating Gearbox away From Engine ==&lt;br /&gt;
&lt;br /&gt;
The official workshop manual now says to undo the bellhousing bolts and lower the gearbox away from the engine. Whoever wrote this must have been smoking something very exotic. The first problem is to locate all the bolts on the bellhousing as they are well hidden. Take a close look at the picture below and locate all the bolts.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 17. Gearbox bolts.png|thumb|left|250px|Figure 17. Gearbox bolts]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
The next problem is undoing them as there is no room to get a socket set in. I had to use a complex combination of extensions and flex joints from two socket sets to get to a couple of the bolts. Also note that there is very little chance of the gearbox falling off once the bolts are undone so don’t spend a lot of time supporting it.&lt;br /&gt;
&lt;br /&gt;
Separating the gearbox from the engine can be a real pain (literally). The gearbox is located on studs and corrosion can hold it in place. I had to hit the bellhousing edge with a large hammer (protecting the metal with a wooden block) before it would separate.&lt;br /&gt;
&lt;br /&gt;
Once it is separated you have to drop the gearbox down. The transmission tunnel is so tight that this appears to be a near impossible task. I had to jack the engine forward to gain as much room as possible. You will also find that the gearbox will move backwards a little way in the tunnel, this means you can then open a useful gap around the clutch.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 18. Pulling the engine forward with strap.png|thumb|left|250px|Figure 18. Pulling the engine forward with strap]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 19. Gap between gearbox and clutch with engine pulled forward.png|thumb|left|250px|Figure 19. Gap between gearbox and clutch with engine pulled forward]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Some people have changed the clutch using just this gap. Instead, I undid the clutch cover bolts and removed the clutch assembly with the gearbox still in place. Removing the clutch then meant there was just enough room for the gearbox to be pulled out.&lt;br /&gt;
&lt;br /&gt;
== Replacing the Clutch ==&lt;br /&gt;
&lt;br /&gt;
Within the clutch kit should be a new cover, new plate and new release bearing.&lt;br /&gt;
&lt;br /&gt;
The old release bearing is removed by prising the spring clip out of the mounting and sliding it out of the spring. Re-assembly is just as easy, make sure that the splines are lightly greased and the inside of the release bearing where it slides on the shaft is greased (not the bearing itself – this should be lubricated by the factory).&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 20. Clutch Release Bearing.png|thumb|left|250px|Figure 20. Clutch Release Bearing]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Put grease on the moving points of the clutch release arm as well.&lt;br /&gt;
&lt;br /&gt;
The pictures below shows the clutch mechanism. I purchased a cheap kit (CPK1086) from ebay. The quality seems ok (it is stamped as being made by AISIN – who supply Suzuki with parts), the only issue being that it was supplied with the incorrect release bearing. The company immediately shipped the correct bearing free of charge and assured me that the correct bearing should have been in the kit. Also note that the new plate has 4 springs whilst the old one has 3, again I have been assured that this is ok.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 21. Wrong Release Bearing is on Right.png|thumb|left|250px|Figure 21. Wrong Release Bearing is on Right]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 22. New Clutch Plate on left.png|thumb|left|250px|Figure 22. New Clutch Plate on left]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 23. New clutch cover on left.png|thumb|left|250px|Figure 23. New clutch cover on left]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Assemble the new clutch mechanism using a clutch alignment tool (I got mine cheap - £1 – as it was a girlie pink colour and had remained unsold in the shop for a long time). With this tool you assemble the clutch off the car and then lift the whole unit into place and bolt down the clutch cover to the flywheel. Remove clutch alignment tool.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 24. Clutch Assembled.png|thumb|left|250px|Figure 24. Clutch Assembled]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 25. Clutch with alignment tool.png|thumb|left|250px|Figure 25. Clutch with alignment tool]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 26. Clutch back in place.png|thumb|left|250px|Figure 26. Clutch back in place]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Wipe a layer of grease around the mating face of the gearbox, this should mean it doesn’t stick in the future and should make it easier to re-assemble.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 27. Grease the mounting face of the gearbox.png|thumb|left|250px|Figure 27. Grease the mounting face of the gearbox]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
== Refitting the Gearbox ==&lt;br /&gt;
&lt;br /&gt;
With the engine still jacked forward it should be possible to jack the gearbox back into place using the weight of the car to help force it into position. Before trying to mate it back with the clutch allow the engine to drop back into its proper position (not too far back) – this will make it easier to align.&lt;br /&gt;
&lt;br /&gt;
It should now be possible to wiggle the gearbox forward. FIRST OF ALL CHECK NOTHING IS IN THE WAY – I failed to notice the reversing light switch had fallen down and I severed the cable which had become trapped. Fitting the gearbox is one of those tasks where you will have repeated attempts to get it to go and then it will suddenly “click” – it will need lots of tiny jiggles to creep it onto the studs.&lt;br /&gt;
&lt;br /&gt;
Refit all the bolts that hold the gearbox in place (use Copper Grease on the bolts to make it easier next time!)&lt;br /&gt;
&lt;br /&gt;
Now it’s a matter of going back through the steps previously to refit everything.&lt;br /&gt;
&lt;br /&gt;
Note that you may want to fit extended breathers to the gearbox whilst it is in bits. The picture below shows the rubber pipe that is the normal breather (minus a plastic cap which has already fallen off!)&lt;br /&gt;
&lt;br /&gt;
Simply slide some pipe onto the tub and extend the breather to a higher point on the car.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 28. Gearbox breather.png|thumb|left|250px|Figure 28. Gearbox breather]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
&lt;br /&gt;
{{Edited}}&lt;br /&gt;
[[Category:Howto]][[Category:Drivechain]]&lt;/div&gt;</summary>
		<author><name>Leftcase</name></author>
	</entry>
	<entry>
		<id>https://www.bigjimny.com/mediawiki/index.php?title=King_pin_bearing_change&amp;diff=680</id>
		<title>King pin bearing change</title>
		<link rel="alternate" type="text/html" href="https://www.bigjimny.com/mediawiki/index.php?title=King_pin_bearing_change&amp;diff=680"/>
		<updated>2016-06-06T19:43:14Z</updated>

		<summary type="html">&lt;p&gt;Leftcase: &lt;/p&gt;
&lt;hr /&gt;
&lt;div&gt;{{Print|[{{fullurl:{{FULLPAGENAME}}|action=pdfbook&amp;amp;format=single}} Print this page as a PDF]}}&lt;br /&gt;
&lt;br /&gt;
= Changing the Kingpin Bearings =&lt;br /&gt;
&lt;br /&gt;
== Introduction ==&lt;br /&gt;
If you off-road a Jimny (or any of the Suzuki classic 4wd vehicles) then this is&lt;br /&gt;
a job you will become familiar with. It is also one of the worst in my opinion,&lt;br /&gt;
not because it is difficult, but because of the smell, you will find out what I&lt;br /&gt;
mean later.&lt;br /&gt;
&lt;br /&gt;
It is also closely tied in with changing/working on the wheel bearings so some&lt;br /&gt;
of the steps are duplicated.&lt;br /&gt;
So what are the symptoms of worn KingPin bearings:&lt;br /&gt;
* Steering Shimmy, see [[Death_Wobble | Death Wobble ]]&lt;br /&gt;
* Oil/Grease leaking from Swivel Joint&lt;br /&gt;
* Vertical play in the front wheel (with the car jacked up grip the wheel top and bottom and rock it, there will be movement if they are worn, get an assistant to press the brakes, if it still wobbles then it is the Kingpin bearings.)&lt;br /&gt;
&lt;br /&gt;
[[File:leaky_swivel.jpg|thumb|left|250px|Leaking front swivel]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
It is also common not to experience any play at all and to even pass an MOT with a really bad bearing. This is because the bottom bearing in particular can rust solid so no play is detectable. The worst Jimnys for this are often the &amp;quot;one careful lady owner&amp;quot; ones that have sat for long periods on the driveway with the bottom bearing rusting away.&lt;br /&gt;
&lt;br /&gt;
----&lt;br /&gt;
&lt;br /&gt;
== Changing the bearings ==&lt;br /&gt;
=== Tools ===&lt;br /&gt;
{{tools|&amp;lt;ul&amp;gt;&amp;lt;li&amp;gt; Standard metric sockets and spanners&amp;lt;/li&amp;gt;&amp;lt;li&amp;gt;Assorted screwdrivers&amp;lt;/li&amp;gt;&amp;lt;li&amp;gt;Circlip pliers (External)&amp;lt;/li&amp;gt;&amp;lt;li&amp;gt;An E10 Torx socket for the Vacuum Hub Bolts&amp;lt;/li&amp;gt;&amp;lt;li&amp;gt;A ball joint splitter&amp;lt;/li&amp;gt;&amp;lt;li&amp;gt;1&amp;quot; Imperial Socket&amp;lt;/li&amp;gt;&amp;lt;li&amp;gt;G-Clamp or brake piston retractor&amp;lt;/li&amp;gt;&amp;lt;/ul&amp;gt;&lt;br /&gt;
&amp;lt;br&amp;gt;&lt;br /&gt;
}}&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
=== The Video ===&lt;br /&gt;
Before you read the guide below you may wish to view the video. This shows the changing of the Kingpin Bearings on a Jimny fitted with ABS so you will see me remove the sensor etc.&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&amp;lt;youtube&amp;gt;LMDyMmJ3VK0&amp;lt;/youtube&amp;gt;&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
The rest of the guide below shows the same task in a series of steps for clarity&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
=== Removing the Caliper and pads ===&lt;br /&gt;
[[File:Caliper.jpg|thumb|left|250px|Jimny Front Caliper]]&lt;br /&gt;
First of all secure the car, release the wheel nuts and jack up the car and remove the road wheel. This then reveals the [[Wikipedia:brake caliper | brake caliper]], this is the passenger side (nearside) caliper (UK) &lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
[[File:Unbolt_caliper.jpg|thumb|left|250px|Unbolting the caliper]]&lt;br /&gt;
Using a 12mm spanner, release the front caliper bolt (the left is the front of the car in this picture) and loosen the same bolt on the rear of the caliper.&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
[[File:Open_caliper.jpg|thumb|left|250x250px|Open brake caliper]]&lt;br /&gt;
The caliper then opens up using the rear bolt as a hinge.&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
[[File:Removing_pads.jpg|thumb|left|250x250px|Removing the brake pads]]&lt;br /&gt;
The pads are retained by small spring clips, a simple pull on the pads (horizontally away from the disk) should remove them (or gently prise out the pads with a small screwdriver - do not remove the spring clips). If you require new [https://www.bigjimny.com/store/front-brake-pads-aisin-suzuki-jimny.html pads], [https://www.bigjimny.com/store/front-pad-fitting-kit.html spring clips] or a [https://www.bigjimny.com/store/caliper-fitting-kit-aisin-suzuki-jimny.html caliper fitting kit] then these are available in the [https://www.bigjimny.com/store/ BigJimny Store].&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
=== Removing the Brake Disc ===&lt;br /&gt;
&lt;br /&gt;
[[File:Carrier_bolt.jpg|thumb|250px|left|Carrier bolt]]&lt;br /&gt;
The caliper is held on with two bolts at the rear (see below).&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
[[File:Carrier_to_spring.jpg|thumb|250px|left|Caliper tied to Spring]]&lt;br /&gt;
Release the bolts and tie the caliper to the spring to keep it out of the way.&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
[[File:Disc_removal.jpg|thumb|250px|left|Disc removal using bolt]]&lt;br /&gt;
Now the front brake disc can be removed. If you are lucky it will simply pull off but if you have problems then there are two M8 holes in the disk hub. Simply run two bolts into these holes and the disk will push off the hub. The picture below shows a bolt being used to push the disk off the hub.&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
My disk appeared to be ok on the visible side but the rear showed some bad wear so I will change them as part of this job. New [https://www.bigjimny.com/store/brake-disc-suzuki-jimny-107mm.html disks] are available in the [https://www.bigjimny.com/store/ BigJimny Store].&lt;br /&gt;
&amp;lt;gallery widths=250 heights=250&amp;gt;&lt;br /&gt;
Disc_front.jpg&lt;br /&gt;
Disk_rear.jpg&lt;br /&gt;
&amp;lt;/gallery&amp;gt;&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
=== Dismantling the Hub ===&lt;br /&gt;
&lt;br /&gt;
[[File:freewheelinghub.jpg|thumb|250px|left|Torx bolt on hub]]&lt;br /&gt;
Now the Freewheeling Hub needs to be removed. Suzuki have used Torx bolts to secure these so you will require an E10 socket to remove the bolts.&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
[[File:hubcirclip.jpg|thumb|250px|left|Removing the circlip]]&lt;br /&gt;
With the hub removed the driveshaft is exposed. The driveshaft is retained with a circlip so use a pair of circlip pliers to remove it. This is really fiddly and can be an annoying task. Behind the circlip is a rectangular washer that should also be removed. Note that I have also marked with white paint the orientation of the freewheeling hub, this is not strictly needed.&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
[[File:vacuumpipe.jpg|thumb|250px|left|removing a vacuum pipe]]&lt;br /&gt;
Gently pull the two vacuum hoses for the hub from the knuckle making sure you note which one connects to each pipe. It is essential that you get this correct else the hub will not work again. Also note that if you have an ABS equipped vehicle then you will have to remove the sensor. I do not have photos of this but the video shows it. IT IS REALLY EASY TO SHEAR THE ABS BOLT - if you can I would soak it for a couple of days previously in penetrating oil.&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
[[File:swivelsealbolts.jpg|thumb|250x250px|left|Removing the swivel seal bolts]]&lt;br /&gt;
At the rear of the hub release the small bolts holding the seal and retainer. You can see that the swivel hub is covered in oil, a bad sign for KingPin problems.&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
[[File:balljointsplitter.jpg|thumb|250px|left|Splitting the ball joint]]&lt;br /&gt;
Undo the nuts on the steering joints, if the joint rotates then put a jack under the joint and lift the car slightly to lock the joint. Using a splitter, split the steering joints (two to do on the passenger side and one on the drivers side – UK).&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
[[File:kingpinbolts.jpg|thumb|250px|left|undoing the Kingpin bolts]]&lt;br /&gt;
Finally, release the KingPin bolts themselves. There are two sets, top and bottom and they must not be mixed up so you can see in the picture that I have marked them up with a letter T. If you are doing both sides at once then do not mix them across either!.&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
The KingPins are also held in with sticky sealant so you will need to prise them out. The hub will now pull off. Beware, if they are badly worn the hub will be full of stinking grease, oil and water so make sure you can capture the mess in something. This is the bit I hate because of the smell!.&lt;br /&gt;
That’s water pouring out of the axle! Also shown is a worn out bearing.&lt;br /&gt;
&amp;lt;gallery widths=250px heights=250px&amp;gt;&lt;br /&gt;
leakingswivel1.jpg&lt;br /&gt;
leakingswivel2.jpg&lt;br /&gt;
wornbearing.jpg&lt;br /&gt;
&amp;lt;/gallery&amp;gt;&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
The bearings are Koyo brand as standard. The BigJimny store has two kits available, the [https://www.bigjimny.com/store/kingpin-bearing-kit-suzuki-jimny-koyo.html basic kit] has the two bearings and the small oil seal required to do one side. The [https://www.bigjimny.com/store/kingpin-bearing/seal-kit-suzuki-jimny.html full kit] also included the large external seal although some people choose not to change this. The thing to remember is that it is not a Landrover which has oil filled swivels. The joints on Jimnys should be &amp;quot;dry&amp;quot; apart from some lubricating grease.&lt;br /&gt;
&lt;br /&gt;
The next stage is to CLEAN, CLEAN and then CLEAN again. Clean the swivels inside and out, clean the knuckles and pull out the drive shaft and clean that as well.&lt;br /&gt;
&lt;br /&gt;
=== The rebuild ===&lt;br /&gt;
&lt;br /&gt;
[[File:outerrace.jpg|thumb|250px|left|The old bearing race]]&lt;br /&gt;
Once clean you can start the rebuild process. The KingPin bearings come in two parts, the race and an outer ring. This ring is still in the swivel and needs driving out. &lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
[[File:Remove Bearing Race.jpg|thumb|250px|left|Removing the bearing race]]&lt;br /&gt;
A simple way to drive them out is to use a 1&amp;quot; Imperial socket. Using an extension bar fed through the swivel place the 1&amp;quot; Socket behind the ring and drive it out by hitting it. (picture from Dave at [http://www.bits4vits.co.uk Bits4Vits] &lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
The new rings can then be driven into place with a piece of wood to protect them from the hammer, again this is seen in the video {{color|green|(&#039;&#039;picture needed here&#039;&#039;)}}. &lt;br /&gt;
&lt;br /&gt;
I also hooked out the small axle shaft oil seal and put a new one in from the BigJimny kit. {{color|green|(&#039;&#039;picture needed here&#039;&#039;)}}. &lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
[[File:rebuiltswivel.jpg|thumb|250px|left|The rebuilt swivel]]&lt;br /&gt;
Here is the completed swivel with new rings and oil seal (and plenty of copper grease to help them all into place.&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
If you are changing the large seal then now is the time to put the new one on. The confusing part is the order of the seals and rings on the swivel, the picture below is of the correct orientation, note also that the slits in the retainers go to the top.&lt;br /&gt;
&amp;lt;gallery widths=250 heights=250&amp;gt;&lt;br /&gt;
seal1.jpg&lt;br /&gt;
seal2.jpg&lt;br /&gt;
&amp;lt;/gallery&amp;gt;&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
[[File:cvjoint.jpg|thumb|250px|left|The greased CV joint]]&lt;br /&gt;
Pack the CV with grease (but do not overpack) and re-fit the driveshaft. A suitable [https://www.bigjimny.com/store/waterproof-grease.html waterproof grease] is available in the BigJimny Shop.&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
[[File:sealant.jpg|thumb|250px|left|Applying sealant]]&lt;br /&gt;
Grease the new KingPin bearings and insert the top one in the carrier. I find the easiest way to grease the bearings is to put them in a polythene bag with some grease and use thebag to squeeze the grease into the bearing, this can be seen in the video. (&#039;&#039;picture needed here&#039;&#039;) .Carefully insert the new bottom bearing and, holding it in place, slide the whole knuckle onto the hub. Fill the Knuckle with 100ml of grease, Suzuki recommend only 100ml and not to overfill. Now the KingPins need to be inserted, but first they need a bead of sealant around the KingPin. Again the BigJimny shop sells suitable [https://www.bigjimny.com/store/loctite-premium-copper/silicone-sealant.html sealant].&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
Make sure that you have put the correct Kingpin in place, remember you should have marked them when you dismantled it!&lt;br /&gt;
&lt;br /&gt;
Bolt the Kingpins in and tighten them to the correct torque (18ft/lbs) &lt;br /&gt;
&lt;br /&gt;
Refit the steering arm (or arms if it is the side with two connections), tightening the nuts to 31ft/lbs&lt;br /&gt;
&lt;br /&gt;
&lt;br /&gt;
Fit the disk and fit the caliper (Caliper bolts 61ft/lbs), brake pads and bolt the caliper down in position (Caliper pin bolt 16/ft/lbs)&lt;br /&gt;
&lt;br /&gt;
Re-fit the wheel and lower the vehicle.&lt;br /&gt;
&lt;br /&gt;
=== Torque Settings ===&lt;br /&gt;
Full details of the torque settings can be found in the [[Torque#Front_Hub | reference data]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
{{Edited}}&lt;br /&gt;
[[Category:Howto]][[Category:Steering]]&lt;/div&gt;</summary>
		<author><name>Leftcase</name></author>
	</entry>
	<entry>
		<id>https://www.bigjimny.com/mediawiki/index.php?title=King_pin_bearing_change&amp;diff=679</id>
		<title>King pin bearing change</title>
		<link rel="alternate" type="text/html" href="https://www.bigjimny.com/mediawiki/index.php?title=King_pin_bearing_change&amp;diff=679"/>
		<updated>2016-06-06T19:41:18Z</updated>

		<summary type="html">&lt;p&gt;Leftcase: &lt;/p&gt;
&lt;hr /&gt;
&lt;div&gt;{{Print|[{{fullurl:{{FULLPAGENAME}}|action=pdfbook&amp;amp;format=single}} Print this page as a PDF]}}&lt;br /&gt;
= Changing the Kingpin Bearings =&lt;br /&gt;
&lt;br /&gt;
== Introduction ==&lt;br /&gt;
If you off-road a Jimny (or any of the Suzuki classic 4wd vehicles) then this is&lt;br /&gt;
a job you will become familiar with. It is also one of the worst in my opinion,&lt;br /&gt;
not because it is difficult, but because of the smell, you will find out what I&lt;br /&gt;
mean later.&lt;br /&gt;
&lt;br /&gt;
It is also closely tied in with changing/working on the wheel bearings so some&lt;br /&gt;
of the steps are duplicated.&lt;br /&gt;
So what are the symptoms of worn KingPin bearings:&lt;br /&gt;
* Steering Shimmy, see [[Death_Wobble | Death Wobble ]]&lt;br /&gt;
* Oil/Grease leaking from Swivel Joint&lt;br /&gt;
* Vertical play in the front wheel (with the car jacked up grip the wheel top and bottom and rock it, there will be movement if they are worn, get an assistant to press the brakes, if it still wobbles then it is the Kingpin bearings.)&lt;br /&gt;
&lt;br /&gt;
[[File:leaky_swivel.jpg|thumb|left|250px|Leaking front swivel]]{{note|Click on images to make them larger}} &lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
It is also common not to experience any play at all and to even pass an MOT with a really bad bearing. This is because the bottom bearing in particular can rust solid so no play is detectable. The worst Jimnys for this are often the &amp;quot;one careful lady owner&amp;quot; ones that have sat for long periods on the driveway with the bottom bearing rusting away.&lt;br /&gt;
&lt;br /&gt;
----&lt;br /&gt;
&lt;br /&gt;
== Changing the bearings ==&lt;br /&gt;
=== Tools ===&lt;br /&gt;
{{tools|&amp;lt;ul&amp;gt;&amp;lt;li&amp;gt; Standard metric sockets and spanners&amp;lt;/li&amp;gt;&amp;lt;li&amp;gt;Assorted screwdrivers&amp;lt;/li&amp;gt;&amp;lt;li&amp;gt;Circlip pliers (External)&amp;lt;/li&amp;gt;&amp;lt;li&amp;gt;An E10 Torx socket for the Vacuum Hub Bolts&amp;lt;/li&amp;gt;&amp;lt;li&amp;gt;A ball joint splitter&amp;lt;/li&amp;gt;&amp;lt;li&amp;gt;1&amp;quot; Imperial Socket&amp;lt;/li&amp;gt;&amp;lt;li&amp;gt;G-Clamp or brake piston retractor&amp;lt;/li&amp;gt;&amp;lt;/ul&amp;gt;&lt;br /&gt;
&amp;lt;br&amp;gt;&lt;br /&gt;
}}&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
=== The Video ===&lt;br /&gt;
Before you read the guide below you may wish to view the video. This shows the changing of the Kingpin Bearings on a Jimny fitted with ABS so you will see me remove the sensor etc.&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&amp;lt;youtube&amp;gt;LMDyMmJ3VK0&amp;lt;/youtube&amp;gt;&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
The rest of the guide below shows the same task in a series of steps for clarity&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
=== Removing the Caliper and pads ===&lt;br /&gt;
[[File:Caliper.jpg|thumb|left|250px|Jimny Front Caliper]]&lt;br /&gt;
First of all secure the car, release the wheel nuts and jack up the car and remove the road wheel. This then reveals the [[Wikipedia:brake caliper | brake caliper]], this is the passenger side (nearside) caliper (UK) &lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
[[File:Unbolt_caliper.jpg|thumb|left|250px|Unbolting the caliper]]&lt;br /&gt;
Using a 12mm spanner, release the front caliper bolt (the left is the front of the car in this picture) and loosen the same bolt on the rear of the caliper.&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
[[File:Open_caliper.jpg|thumb|left|250x250px|Open brake caliper]]&lt;br /&gt;
The caliper then opens up using the rear bolt as a hinge.&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
[[File:Removing_pads.jpg|thumb|left|250x250px|Removing the brake pads]]&lt;br /&gt;
The pads are retained by small spring clips, a simple pull on the pads (horizontally away from the disk) should remove them (or gently prise out the pads with a small screwdriver - do not remove the spring clips). If you require new [https://www.bigjimny.com/store/front-brake-pads-aisin-suzuki-jimny.html pads], [https://www.bigjimny.com/store/front-pad-fitting-kit.html spring clips] or a [https://www.bigjimny.com/store/caliper-fitting-kit-aisin-suzuki-jimny.html caliper fitting kit] then these are available in the [https://www.bigjimny.com/store/ BigJimny Store].&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
=== Removing the Brake Disc ===&lt;br /&gt;
&lt;br /&gt;
[[File:Carrier_bolt.jpg|thumb|250px|left|Carrier bolt]]&lt;br /&gt;
The caliper is held on with two bolts at the rear (see below).&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
[[File:Carrier_to_spring.jpg|thumb|250px|left|Caliper tied to Spring]]&lt;br /&gt;
Release the bolts and tie the caliper to the spring to keep it out of the way.&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
[[File:Disc_removal.jpg|thumb|250px|left|Disc removal using bolt]]&lt;br /&gt;
Now the front brake disc can be removed. If you are lucky it will simply pull off but if you have problems then there are two M8 holes in the disk hub. Simply run two bolts into these holes and the disk will push off the hub. The picture below shows a bolt being used to push the disk off the hub.&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
My disk appeared to be ok on the visible side but the rear showed some bad wear so I will change them as part of this job. New [https://www.bigjimny.com/store/brake-disc-suzuki-jimny-107mm.html disks] are available in the [https://www.bigjimny.com/store/ BigJimny Store].&lt;br /&gt;
&amp;lt;gallery widths=250 heights=250&amp;gt;&lt;br /&gt;
Disc_front.jpg&lt;br /&gt;
Disk_rear.jpg&lt;br /&gt;
&amp;lt;/gallery&amp;gt;&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
=== Dismantling the Hub ===&lt;br /&gt;
&lt;br /&gt;
[[File:freewheelinghub.jpg|thumb|250px|left|Torx bolt on hub]]&lt;br /&gt;
Now the Freewheeling Hub needs to be removed. Suzuki have used Torx bolts to secure these so you will require an E10 socket to remove the bolts.&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
[[File:hubcirclip.jpg|thumb|250px|left|Removing the circlip]]&lt;br /&gt;
With the hub removed the driveshaft is exposed. The driveshaft is retained with a circlip so use a pair of circlip pliers to remove it. This is really fiddly and can be an annoying task. Behind the circlip is a rectangular washer that should also be removed. Note that I have also marked with white paint the orientation of the freewheeling hub, this is not strictly needed.&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
[[File:vacuumpipe.jpg|thumb|250px|left|removing a vacuum pipe]]&lt;br /&gt;
Gently pull the two vacuum hoses for the hub from the knuckle making sure you note which one connects to each pipe. It is essential that you get this correct else the hub will not work again. Also note that if you have an ABS equipped vehicle then you will have to remove the sensor. I do not have photos of this but the video shows it. IT IS REALLY EASY TO SHEAR THE ABS BOLT - if you can I would soak it for a couple of days previously in penetrating oil.&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
[[File:swivelsealbolts.jpg|thumb|250x250px|left|Removing the swivel seal bolts]]&lt;br /&gt;
At the rear of the hub release the small bolts holding the seal and retainer. You can see that the swivel hub is covered in oil, a bad sign for KingPin problems.&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
[[File:balljointsplitter.jpg|thumb|250px|left|Splitting the ball joint]]&lt;br /&gt;
Undo the nuts on the steering joints, if the joint rotates then put a jack under the joint and lift the car slightly to lock the joint. Using a splitter, split the steering joints (two to do on the passenger side and one on the drivers side – UK).&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
[[File:kingpinbolts.jpg|thumb|250px|left|undoing the Kingpin bolts]]&lt;br /&gt;
Finally, release the KingPin bolts themselves. There are two sets, top and bottom and they must not be mixed up so you can see in the picture that I have marked them up with a letter T. If you are doing both sides at once then do not mix them across either!.&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
The KingPins are also held in with sticky sealant so you will need to prise them out. The hub will now pull off. Beware, if they are badly worn the hub will be full of stinking grease, oil and water so make sure you can capture the mess in something. This is the bit I hate because of the smell!.&lt;br /&gt;
That’s water pouring out of the axle! Also shown is a worn out bearing.&lt;br /&gt;
&amp;lt;gallery widths=250px heights=250px&amp;gt;&lt;br /&gt;
leakingswivel1.jpg&lt;br /&gt;
leakingswivel2.jpg&lt;br /&gt;
wornbearing.jpg&lt;br /&gt;
&amp;lt;/gallery&amp;gt;&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
The bearings are Koyo brand as standard. The BigJimny store has two kits available, the [https://www.bigjimny.com/store/kingpin-bearing-kit-suzuki-jimny-koyo.html basic kit] has the two bearings and the small oil seal required to do one side. The [https://www.bigjimny.com/store/kingpin-bearing/seal-kit-suzuki-jimny.html full kit] also included the large external seal although some people choose not to change this. The thing to remember is that it is not a Landrover which has oil filled swivels. The joints on Jimnys should be &amp;quot;dry&amp;quot; apart from some lubricating grease.&lt;br /&gt;
&lt;br /&gt;
The next stage is to CLEAN, CLEAN and then CLEAN again. Clean the swivels inside and out, clean the knuckles and pull out the drive shaft and clean that as well.&lt;br /&gt;
&lt;br /&gt;
=== The rebuild ===&lt;br /&gt;
&lt;br /&gt;
[[File:outerrace.jpg|thumb|250px|left|The old bearing race]]&lt;br /&gt;
Once clean you can start the rebuild process. The KingPin bearings come in two parts, the race and an outer ring. This ring is still in the swivel and needs driving out. &lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
[[File:Remove Bearing Race.jpg|thumb|250px|left|Removing the bearing race]]&lt;br /&gt;
A simple way to drive them out is to use a 1&amp;quot; Imperial socket. Using an extension bar fed through the swivel place the 1&amp;quot; Socket behind the ring and drive it out by hitting it. (picture from Dave at [http://www.bits4vits.co.uk Bits4Vits] &lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
The new rings can then be driven into place with a piece of wood to protect them from the hammer, again this is seen in the video {{color|green|(&#039;&#039;picture needed here&#039;&#039;)}}. &lt;br /&gt;
&lt;br /&gt;
I also hooked out the small axle shaft oil seal and put a new one in from the BigJimny kit. {{color|green|(&#039;&#039;picture needed here&#039;&#039;)}}. &lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
[[File:rebuiltswivel.jpg|thumb|250px|left|The rebuilt swivel]]&lt;br /&gt;
Here is the completed swivel with new rings and oil seal (and plenty of copper grease to help them all into place.&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
If you are changing the large seal then now is the time to put the new one on. The confusing part is the order of the seals and rings on the swivel, the picture below is of the correct orientation, note also that the slits in the retainers go to the top.&lt;br /&gt;
&amp;lt;gallery widths=250 heights=250&amp;gt;&lt;br /&gt;
seal1.jpg&lt;br /&gt;
seal2.jpg&lt;br /&gt;
&amp;lt;/gallery&amp;gt;&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
[[File:cvjoint.jpg|thumb|250px|left|The greased CV joint]]&lt;br /&gt;
Pack the CV with grease (but do not overpack) and re-fit the driveshaft. A suitable [https://www.bigjimny.com/store/waterproof-grease.html waterproof grease] is available in the BigJimny Shop.&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
[[File:sealant.jpg|thumb|250px|left|Applying sealant]]&lt;br /&gt;
Grease the new KingPin bearings and insert the top one in the carrier. I find the easiest way to grease the bearings is to put them in a polythene bag with some grease and use thebag to squeeze the grease into the bearing, this can be seen in the video. (&#039;&#039;picture needed here&#039;&#039;) .Carefully insert the new bottom bearing and, holding it in place, slide the whole knuckle onto the hub. Fill the Knuckle with 100ml of grease, Suzuki recommend only 100ml and not to overfill. Now the KingPins need to be inserted, but first they need a bead of sealant around the KingPin. Again the BigJimny shop sells suitable [https://www.bigjimny.com/store/loctite-premium-copper/silicone-sealant.html sealant].&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
Make sure that you have put the correct Kingpin in place, remember you should have marked them when you dismantled it!&lt;br /&gt;
&lt;br /&gt;
Bolt the Kingpins in and tighten them to the correct torque (18ft/lbs) &lt;br /&gt;
&lt;br /&gt;
Refit the steering arm (or arms if it is the side with two connections), tightening the nuts to 31ft/lbs&lt;br /&gt;
&lt;br /&gt;
&lt;br /&gt;
Fit the disk and fit the caliper (Caliper bolts 61ft/lbs), brake pads and bolt the caliper down in position (Caliper pin bolt 16/ft/lbs)&lt;br /&gt;
&lt;br /&gt;
Re-fit the wheel and lower the vehicle.&lt;br /&gt;
&lt;br /&gt;
=== Torque Settings ===&lt;br /&gt;
Full details of the torque settings can be found in the [[Torque#Front_Hub | reference data]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
{{Edited}}&lt;br /&gt;
[[Category:Howto]][[Category:Steering]]&lt;/div&gt;</summary>
		<author><name>Leftcase</name></author>
	</entry>
	<entry>
		<id>https://www.bigjimny.com/mediawiki/index.php?title=Oil_and_air_filter_change&amp;diff=678</id>
		<title>Oil and air filter change</title>
		<link rel="alternate" type="text/html" href="https://www.bigjimny.com/mediawiki/index.php?title=Oil_and_air_filter_change&amp;diff=678"/>
		<updated>2016-06-06T19:40:03Z</updated>

		<summary type="html">&lt;p&gt;Leftcase: &lt;/p&gt;
&lt;hr /&gt;
&lt;div&gt;&lt;br /&gt;
= Changing the Sparkplugs/Oil Filter/Air Filter =&lt;br /&gt;
&lt;br /&gt;
== Introduction ==&lt;br /&gt;
A video guide to changing some basic filters&lt;br /&gt;
&lt;br /&gt;
The parts can be bought from the BigJimny shop:&lt;br /&gt;
&lt;br /&gt;
*[https://www.bigjimny.com/store/oil-filter-suzuki-jimny.html Oil Filter]&lt;br /&gt;
*[https://www.bigjimny.com/store/sump-plug-gasket.html Sump Plug Gasket]&lt;br /&gt;
*[https://www.bigjimny.com/store/air-filter-suzuki-jimny.html Air Filter]&lt;br /&gt;
*[https://www.bigjimny.com/store/spark-plugs.html Spark Plugs]&lt;br /&gt;
*[[Forecourt|Table of Oil Types]] &lt;br /&gt;
&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
----&lt;br /&gt;
&lt;br /&gt;
== Changing/Installing a Filter ==&lt;br /&gt;
=== Tools ===&lt;br /&gt;
{{tools|&amp;lt;ul&amp;gt;&amp;lt;li&amp;gt;Assorted screwdrivers&amp;lt;/li&amp;gt;&amp;lt;li&amp;gt;Standard Metric Socket set&amp;lt;/li&amp;gt;&amp;lt;li&amp;gt;Oil Filter Wrench&amp;lt;/li&amp;gt;&amp;lt;/ul&amp;gt;&lt;br /&gt;
&amp;lt;br&amp;gt;&lt;br /&gt;
}}&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
&lt;br /&gt;
&amp;lt;youtube&amp;gt;dANQDqT2EOo&amp;lt;/youtube&amp;gt;&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
{{Edited}}&lt;br /&gt;
[[Category:Howto]][[Category:Engine]][[Category:Forecourt]]&lt;/div&gt;</summary>
		<author><name>Leftcase</name></author>
	</entry>
	<entry>
		<id>https://www.bigjimny.com/mediawiki/index.php?title=File:Gear_box_breather,_factory_fitment_-_A01.png&amp;diff=633</id>
		<title>File:Gear box breather, factory fitment - A01.png</title>
		<link rel="alternate" type="text/html" href="https://www.bigjimny.com/mediawiki/index.php?title=File:Gear_box_breather,_factory_fitment_-_A01.png&amp;diff=633"/>
		<updated>2016-06-03T20:08:13Z</updated>

		<summary type="html">&lt;p&gt;Leftcase: &lt;/p&gt;
&lt;hr /&gt;
&lt;div&gt;&lt;/div&gt;</summary>
		<author><name>Leftcase</name></author>
	</entry>
	<entry>
		<id>https://www.bigjimny.com/mediawiki/index.php?title=Clutch_replacement&amp;diff=632</id>
		<title>Clutch replacement</title>
		<link rel="alternate" type="text/html" href="https://www.bigjimny.com/mediawiki/index.php?title=Clutch_replacement&amp;diff=632"/>
		<updated>2016-06-03T20:07:52Z</updated>

		<summary type="html">&lt;p&gt;Leftcase: &lt;/p&gt;
&lt;hr /&gt;
&lt;div&gt;&lt;br /&gt;
== A guide to changing the clutch. ==&lt;br /&gt;
&lt;br /&gt;
It is inevitable that at some point you will have to face changing the clutch. It dips in and out of the mud on a regular basis as the bell-housing is not sealed. Eventually the clutch thrust bearing will start rattling and the action will become stiff and heavy.&lt;br /&gt;
Changing the clutch on a Jimny seems to be not for the faint hearted. It’s a very physical task and it is not pleasant struggling with the gearbox under the car, it is a very tight fit in the transmission tunnel.&lt;br /&gt;
&lt;br /&gt;
No special tools are required, but a good toolkit is needed. You will need extension bars for a socket set as some of the bolts are well hidden and difficult to access.&lt;br /&gt;
A breaker bar is also needed as some bolts are very tight.&lt;br /&gt;
&lt;br /&gt;
If this hasn’t put you off then its time to start work. It goes without saying that you should jet-wash the underside of the car if possible to remove as much of the muck before it drops on you!&lt;br /&gt;
There are two ways of changing the clutch, one is to take the engine and gearbox out and the other is to drop the gearbox off. The Suzuki factory manual suggests the gearbox dropping method so that is the way I have gone.&lt;br /&gt;
&lt;br /&gt;
The factory manual suggests it is not necessary to remove the transfer box, but I have removed it as you will need all the space you can get, I thoroughly recommend that you also remove the transfer box.&lt;br /&gt;
&lt;br /&gt;
If you have the luxury of a bit of time then spray the visible bolts with WD40 a day or so before. In particular you should try and spray the bolts holding the exhaust front section and the bolts around the gearbox housing as these are difficult.&lt;br /&gt;
&lt;br /&gt;
Starting inside the car it is necessary to remove both the gear lever and the transfer box lever.&lt;br /&gt;
&lt;br /&gt;
To remove the gearbox lever you have to remove the centre console. This is held on by four screws on the side at the front and back.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 1. Removing the Centre Console.png|thumb|left|250px|Figure 1. Removing the Centre Console]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
The console then lifts out. Mine was more of a problem as I have a switch panel fitted so I then needed to remove the gearlever before the console would come completely away, but this has to be done at some point anyway. Pull the gaiter away to reveal the three bolt heads around the base of the gearlever, undo the bolts and carefully lift out the gearstick, note that there is a small spring and a cup that should not be lost!&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 2. Removing the Gearlever.png|thumb|left|250px|Figure 2. Removing the Gearlever]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
With the console removed you will then see a frame that holds in a second gaiter. Simply undo the bolts and lift the frame clear.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 3. Removing the lower Gaiter.png|thumb|left|250px|Figure 3. Removing the lower Gaiter]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
If you are removing the Transfer Box then you need to remove the gaiter etc. around the Transfer Box Level. First locate the small screw at the rear of the transfer knob and remove it.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 4. Removing the Transfer Lever Knob.png|thumb|left|250px|Figure 4. Removing the Transfer Lever Knob]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Unscrew the frame around the gaiter and pull the frame and gaiter clear.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 5. Removing the Transfer Level Gaiter.png|thumb|left|250px|Figure 5. Removing the Transfer Level Gaiter]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Move outside the car and disconnect the negative cable at battery.&lt;br /&gt;
Now drain the oil from the gearbox and transfer box, if you are not doing any work on the transfer box then it is not strictly necessary to drain the oil providing you keep it upright to stop the oil coming out of the lever hole.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 6. Gearbox Drain Plugs.png|thumb|left|250px|Figure 6. Gearbox Drain Plugs]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
On my Jimny the drain plugs are square and therefore the square end of a 3/8 socket driver fits. Always undo the filler plug first because if the filler is stuck you do not want to drain the oil and not be able to fill it again. The gearbox filler is hidden up the side of the gearbox and lack of space is a problem&lt;br /&gt;
&lt;br /&gt;
On the Transfer Box disconnect the 4WD switch wire at coupler and unclamp harness. Then disconnect the speed sensor coupler.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 7. Transfer Box Fillers and Connectors.png|thumb|left|250px|Figure 7. Transfer Box Fillers and Connectors]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Now remove the front section of the exhaust pipe. This is held in place by pairs of springs with bolts inside. Due to the heat and stress the front bolts were really, really difficult to move. So much so I think there is real possibility of shearing them on some cars. There is a pair at the front and a pair at the back.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 8. Exhaust Bolts.png|thumb|left|250px|Figure 8. Exhaust Bolts]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Do not lift the exhaust of the rubber hangers yet. There is a Lambda sensor connected to the top of the catalytic converter.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 9. Lambda Sensor on Converter.png|thumb|left|250px|Figure 9. Lambda Sensor on Converter]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
This needs to be disconnected. The Suzuki manual shows the sensor being unscrewed from the top of the converter. However, the sensor has been subject to red hot heat, water and mud, therefore mine was firmly rusted in. Instead I followed the wiring back up to behind the engine. Just behind the head on the passenger side is a set of connectors, unbolt the connector mounting bracket and prise the Lambda connector apart (this is very stiff as well!).&lt;br /&gt;
&lt;br /&gt;
[[File:Lambda Sensor Connector Behind Here.png|thumb|left|250px|Lambda Sensor Connector Behind Here]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
With the Lambda sensor disconnected you can pull the front exhaust section off the rubber mounts.&lt;br /&gt;
&lt;br /&gt;
Now remove the propshafts. On each shaft paint some marks so they can be rebolted to the flanges in the correct position when you are re-building it. Paint all the flanges and also mark the sliding joint in the front propshaft. Remove the FRONT propshaft FIRST, followed by the Gearbox/Transfer box shaft SECOND. Where possible do the REAR propshaft LAST. Why! – because all the propshaft bolts are quite tight and therefore you need to hold the propshafts in place whilst you try to undo the bolts. As the front hubs are vacuum operated there is no easy way to lock the props if you have disconnected the rear first. With the rear prop still on the rear wheels keep the system locked. I found out this trick the hard way.&lt;br /&gt;
&lt;br /&gt;
[[File:Mark the Propshaft.png|thumb|left|250px|Mark the Propshaft]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Now undo the 3 large mounting nuts on the transfer box mount and the 4 bolts on the mounting flange. Now the transfer box should lift down.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 10. Transfer mounts.png|thumb|left|250px|Figure 10. Transfer mounts]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 11. Transfer Mounts.png|thumb|left|250px|Figure 11. Transfer Mounts]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Now for the complex bit. The Jimny has a remote gearbox mechanism bolted onto the rear of the gearbox and this needs to be removed. It’s probably easier to see the part after it has been removed as it is clearer what you are trying to achieve. Note this is the top view, you will normally be underneath!&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 12. Gearbox Remote Mechanism.png|thumb|left|250px|Figure 12. Gearbox Remote Mechanism]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Remove gear shift control joint bolt and extension rod bolt.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 13. Remote Mechanism in place.png|thumb|left|250px|Figure 13. Remote Mechanism in place]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Remove the Engine Rear Mounting bolts (Three of them, one either side and one in the rubber bit). This is the mount under the gearbox that rests on the chassis crossmember.&lt;br /&gt;
&lt;br /&gt;
Using a long socket extension, reach into the remote mechanism and undo the 4 bolts that connect it to the gearbox. These are hard to reach.&lt;br /&gt;
&lt;br /&gt;
The entire mechanism should then be removeable complete with the mounts. Also unbolt all the other metal bits (including the exhaust mounting rubber) from the rear cross member as you will need to squeeze the Gearbox out later on.&lt;br /&gt;
&lt;br /&gt;
Now remove the reversing light switch. This is on top of the gearbox towards the front and was more accessible from under the bonnet by reaching down the back of the engine on the passenger side (UK). Tie it up out of the way.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 14. Gearbox Reverse Switch.png|thumb|left|250px|Figure 14. Gearbox Reverse Switch]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Now for the next difficult task, removing the starter motor. Clearly Suzuki never considered that a starter motor may go wrong and need replacing as it is in one of the most in-accessible places. First of all check that you have disconnected the battery. Laying under the car reach up the drivers side of the engine and unbolt the two bolts holding the motor in place and easy it back. There is no need to remove it completely and no need to undo all the cables attached to in.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 15. Starter Motor (from underneath car).png|thumb|left|250px|Figure 15. Starter Motor (from underneath car)]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
We are nearly there now. Remove plastic clutch housing cap and prise the end of the clutch cable from clutch release fork. Then undo the two bolts holding the clutch cable to the transmission and withdraw the clutch cable assembly. Also remove the small tin-plate on the bottom front of the clutch housing held on by a pair of small 10mm bolts.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 16. Clutch cable (unhooked).png|thumb|left|250px|Figure 16. Clutch cable (unhooked)]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
The official workshop manual now says to undo the bellhousing bolts and lower the gearbox away from the engine. Whoever wrote this must have been smoking something very exotic. The first problem is to locate all the bolts on the bellhousing as they are well hidden. Take a close look at the picture below and locate all the bolts.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 17. Gearbox bolts.png|thumb|left|250px|Figure 17. Gearbox bolts]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
The next problem is undoing them as there is no room to get a socket set in. I had to use a complex combination of extensions and flex joints from two socket sets to get to a couple of the bolts. Also note that there is very little chance of the gearbox falling off once the bolts are undone so don’t spend a lot of time supporting it.&lt;br /&gt;
&lt;br /&gt;
Separating the gearbox from the engine can be a real pain (literally). The gearbox is located on studs and corrosion can hold it in place. I had to hit the bellhousing edge with a large hammer (protecting the metal with a wooden block) before it would separate.&lt;br /&gt;
&lt;br /&gt;
Once it is separated you have to drop the gearbox down. The transmission tunnel is so tight that this appears to be a near impossible task. I had to jack the engine forward to gain as much room as possible. You will also find that the gearbox will move backwards a little way in the tunnel, this means you can then open a useful gap around the clutch.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 18. Pulling the engine forward with strap.png|thumb|left|250px|Figure 18. Pulling the engine forward with strap]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 19. Gap between gearbox and clutch with engine pulled forward.png|thumb|left|250px|Figure 19. Gap between gearbox and clutch with engine pulled forward]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Some people have changed the clutch using just this gap. Instead, I undid the clutch cover bolts and removed the clutch assembly with the gearbox still in place. Removing the clutch then meant there was just enough room for the gearbox to be pulled out.&lt;br /&gt;
&lt;br /&gt;
Within the clutch kit should be a new cover, new plate and new release bearing.&lt;br /&gt;
&lt;br /&gt;
The old release bearing is removed by prising the spring clip out of the mounting and sliding it out of the spring. Re-assembly is just as easy, make sure that the splines are lightly greased and the inside of the release bearing where it slides on the shaft is greased (not the bearing itself – this should be lubricated by the factory).&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 20. Clutch Release Bearing.png|thumb|left|250px|Figure 20. Clutch Release Bearing]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Put grease on the moving points of the clutch release arm as well.&lt;br /&gt;
&lt;br /&gt;
The pictures below shows the clutch mechanism. I purchased a cheap kit (CPK1086) from ebay. The quality seems ok (it is stamped as being made by AISIN – who supply Suzuki with parts), the only issue being that it was supplied with the incorrect release bearing. The company immediately shipped the correct bearing free of charge and assured me that the correct bearing should have been in the kit. Also note that the new plate has 4 springs whilst the old one has 3, again I have been assured that this is ok.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 21. Wrong Release Bearing is on Right.png|thumb|left|250px|Figure 21. Wrong Release Bearing is on Right]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 22. New Clutch Plate on left.png|thumb|left|250px|Figure 22. New Clutch Plate on left]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 23. New clutch cover on left.png|thumb|left|250px|Figure 23. New clutch cover on left]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Assemble the new clutch mechanism using a clutch alignment tool (I got mine cheap - £1 – as it was a girlie pink colour and had remained unsold in the shop for a long time). With this tool you assemble the clutch off the car and then lift the whole unit into place and bolt down the clutch cover to the flywheel. Remove clutch alignment tool.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 24. Clutch Assembled.png|thumb|left|250px|Figure 24. Clutch Assembled]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 25. Clutch with alignment tool.png|thumb|left|250px|Figure 25. Clutch with alignment tool]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 26. Clutch back in place.png|thumb|left|250px|Figure 26. Clutch back in place]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Wipe a layer of grease around the mating face of the gearbox, this should mean it doesn’t stick in the future and should make it easier to re-assemble.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 27. Grease the mounting face of the gearbox.png|thumb|left|250px|Figure 27. Grease the mounting face of the gearbox]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
With the engine still jacked forward it should be possible to jack the gearbox back into place using the weight of the car to help force it into position. Before trying to mate it back with the clutch allow the engine to drop back into its proper position (not too far back) – this will make it easier to align.&lt;br /&gt;
&lt;br /&gt;
It should now be possible to wiggle the gearbox forward. FIRST OF ALL CHECK NOTHING IS IN THE WAY – I failed to notice the reversing light switch had fallen down and I severed the cable which had become trapped. Fitting the gearbox is one of those tasks where you will have repeated attempts to get it to go and then it will suddenly “click” – it will need lots of tiny jiggles to creep it onto the studs.&lt;br /&gt;
&lt;br /&gt;
Refit all the bolts that hold the gearbox in place (use Copper Grease on the bolts to make it easier next time!)&lt;br /&gt;
&lt;br /&gt;
Now it’s a matter of going back through the steps previously to refit everything.&lt;br /&gt;
&lt;br /&gt;
Note that you may want to fit extended breathers to the gearbox whilst it is in bits. The picture below shows the rubber pipe that is the normal breather (minus a plastic cap which has already fallen off!)&lt;br /&gt;
&lt;br /&gt;
Simply slide some pipe onto the tub and extend the breather to a higher point on the car.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 28. Gearbox breather.png|thumb|left|250px|Figure 28. Gearbox breather]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;/div&gt;</summary>
		<author><name>Leftcase</name></author>
	</entry>
	<entry>
		<id>https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_29_-_grease_the_mounting_face_of_the_gear_box.png&amp;diff=631</id>
		<title>File:Clutch replacement guide - figure 29 - grease the mounting face of the gear box.png</title>
		<link rel="alternate" type="text/html" href="https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_29_-_grease_the_mounting_face_of_the_gear_box.png&amp;diff=631"/>
		<updated>2016-06-03T20:06:00Z</updated>

		<summary type="html">&lt;p&gt;Leftcase: &lt;/p&gt;
&lt;hr /&gt;
&lt;div&gt;&lt;/div&gt;</summary>
		<author><name>Leftcase</name></author>
	</entry>
	<entry>
		<id>https://www.bigjimny.com/mediawiki/index.php?title=Clutch_replacement&amp;diff=630</id>
		<title>Clutch replacement</title>
		<link rel="alternate" type="text/html" href="https://www.bigjimny.com/mediawiki/index.php?title=Clutch_replacement&amp;diff=630"/>
		<updated>2016-06-03T20:04:52Z</updated>

		<summary type="html">&lt;p&gt;Leftcase: &lt;/p&gt;
&lt;hr /&gt;
&lt;div&gt;&lt;br /&gt;
== A guide to changing the clutch. ==&lt;br /&gt;
&lt;br /&gt;
It is inevitable that at some point you will have to face changing the clutch. It dips in and out of the mud on a regular basis as the bell-housing is not sealed. Eventually the clutch thrust bearing will start rattling and the action will become stiff and heavy.&lt;br /&gt;
Changing the clutch on a Jimny seems to be not for the faint hearted. It’s a very physical task and it is not pleasant struggling with the gearbox under the car, it is a very tight fit in the transmission tunnel.&lt;br /&gt;
&lt;br /&gt;
No special tools are required, but a good toolkit is needed. You will need extension bars for a socket set as some of the bolts are well hidden and difficult to access.&lt;br /&gt;
A breaker bar is also needed as some bolts are very tight.&lt;br /&gt;
&lt;br /&gt;
If this hasn’t put you off then its time to start work. It goes without saying that you should jet-wash the underside of the car if possible to remove as much of the muck before it drops on you!&lt;br /&gt;
There are two ways of changing the clutch, one is to take the engine and gearbox out and the other is to drop the gearbox off. The Suzuki factory manual suggests the gearbox dropping method so that is the way I have gone.&lt;br /&gt;
&lt;br /&gt;
The factory manual suggests it is not necessary to remove the transfer box, but I have removed it as you will need all the space you can get, I thoroughly recommend that you also remove the transfer box.&lt;br /&gt;
&lt;br /&gt;
If you have the luxury of a bit of time then spray the visible bolts with WD40 a day or so before. In particular you should try and spray the bolts holding the exhaust front section and the bolts around the gearbox housing as these are difficult.&lt;br /&gt;
&lt;br /&gt;
Starting inside the car it is necessary to remove both the gear lever and the transfer box lever.&lt;br /&gt;
&lt;br /&gt;
To remove the gearbox lever you have to remove the centre console. This is held on by four screws on the side at the front and back.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 1. Removing the Centre Console.png|thumb|left|250px|Figure 1. Removing the Centre Console]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
The console then lifts out. Mine was more of a problem as I have a switch panel fitted so I then needed to remove the gearlever before the console would come completely away, but this has to be done at some point anyway. Pull the gaiter away to reveal the three bolt heads around the base of the gearlever, undo the bolts and carefully lift out the gearstick, note that there is a small spring and a cup that should not be lost!&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 2. Removing the Gearlever.png|thumb|left|250px|Figure 2. Removing the Gearlever]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
With the console removed you will then see a frame that holds in a second gaiter. Simply undo the bolts and lift the frame clear.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 3. Removing the lower Gaiter.png|thumb|left|250px|Figure 3. Removing the lower Gaiter]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
If you are removing the Transfer Box then you need to remove the gaiter etc. around the Transfer Box Level. First locate the small screw at the rear of the transfer knob and remove it.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 4. Removing the Transfer Lever Knob.png|thumb|left|250px|Figure 4. Removing the Transfer Lever Knob]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Unscrew the frame around the gaiter and pull the frame and gaiter clear.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 5. Removing the Transfer Level Gaiter.png|thumb|left|250px|Figure 5. Removing the Transfer Level Gaiter]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Move outside the car and disconnect the negative cable at battery.&lt;br /&gt;
Now drain the oil from the gearbox and transfer box, if you are not doing any work on the transfer box then it is not strictly necessary to drain the oil providing you keep it upright to stop the oil coming out of the lever hole.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 6. Gearbox Drain Plugs.png|thumb|left|250px|Figure 6. Gearbox Drain Plugs]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
On my Jimny the drain plugs are square and therefore the square end of a 3/8 socket driver fits. Always undo the filler plug first because if the filler is stuck you do not want to drain the oil and not be able to fill it again. The gearbox filler is hidden up the side of the gearbox and lack of space is a problem&lt;br /&gt;
&lt;br /&gt;
On the Transfer Box disconnect the 4WD switch wire at coupler and unclamp harness. Then disconnect the speed sensor coupler.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 7. Transfer Box Fillers and Connectors.png|thumb|left|250px|Figure 7. Transfer Box Fillers and Connectors]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Now remove the front section of the exhaust pipe. This is held in place by pairs of springs with bolts inside. Due to the heat and stress the front bolts were really, really difficult to move. So much so I think there is real possibility of shearing them on some cars. There is a pair at the front and a pair at the back.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 8. Exhaust Bolts.png|thumb|left|250px|Figure 8. Exhaust Bolts]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Do not lift the exhaust of the rubber hangers yet. There is a Lambda sensor connected to the top of the catalytic converter.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 9. Lambda Sensor on Converter.png|thumb|left|250px|Figure 9. Lambda Sensor on Converter]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
This needs to be disconnected. The Suzuki manual shows the sensor being unscrewed from the top of the converter. However, the sensor has been subject to red hot heat, water and mud, therefore mine was firmly rusted in. Instead I followed the wiring back up to behind the engine. Just behind the head on the passenger side is a set of connectors, unbolt the connector mounting bracket and prise the Lambda connector apart (this is very stiff as well!).&lt;br /&gt;
&lt;br /&gt;
[[File:Lambda Sensor Connector Behind Here.png|thumb|left|250px|Lambda Sensor Connector Behind Here]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
With the Lambda sensor disconnected you can pull the front exhaust section off the rubber mounts.&lt;br /&gt;
&lt;br /&gt;
Now remove the propshafts. On each shaft paint some marks so they can be rebolted to the flanges in the correct position when you are re-building it. Paint all the flanges and also mark the sliding joint in the front propshaft. Remove the FRONT propshaft FIRST, followed by the Gearbox/Transfer box shaft SECOND. Where possible do the REAR propshaft LAST. Why! – because all the propshaft bolts are quite tight and therefore you need to hold the propshafts in place whilst you try to undo the bolts. As the front hubs are vacuum operated there is no easy way to lock the props if you have disconnected the rear first. With the rear prop still on the rear wheels keep the system locked. I found out this trick the hard way.&lt;br /&gt;
&lt;br /&gt;
[[File:Mark the Propshaft.png|thumb|left|250px|Mark the Propshaft]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Now undo the 3 large mounting nuts on the transfer box mount and the 4 bolts on the mounting flange. Now the transfer box should lift down.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 10. Transfer mounts.png|thumb|left|250px|Figure 10. Transfer mounts]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 11. Transfer Mounts.png|thumb|left|250px|Figure 11. Transfer Mounts]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Now for the complex bit. The Jimny has a remote gearbox mechanism bolted onto the rear of the gearbox and this needs to be removed. It’s probably easier to see the part after it has been removed as it is clearer what you are trying to achieve. Note this is the top view, you will normally be underneath!&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 12. Gearbox Remote Mechanism.png|thumb|left|250px|Figure 12. Gearbox Remote Mechanism]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Remove gear shift control joint bolt and extension rod bolt.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 13. Remote Mechanism in place.png|thumb|left|250px|Figure 13. Remote Mechanism in place]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Remove the Engine Rear Mounting bolts (Three of them, one either side and one in the rubber bit). This is the mount under the gearbox that rests on the chassis crossmember.&lt;br /&gt;
&lt;br /&gt;
Using a long socket extension, reach into the remote mechanism and undo the 4 bolts that connect it to the gearbox. These are hard to reach.&lt;br /&gt;
&lt;br /&gt;
The entire mechanism should then be removeable complete with the mounts. Also unbolt all the other metal bits (including the exhaust mounting rubber) from the rear cross member as you will need to squeeze the Gearbox out later on.&lt;br /&gt;
&lt;br /&gt;
Now remove the reversing light switch. This is on top of the gearbox towards the front and was more accessible from under the bonnet by reaching down the back of the engine on the passenger side (UK). Tie it up out of the way.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 14. Gearbox Reverse Switch.png|thumb|left|250px|Figure 14. Gearbox Reverse Switch]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Now for the next difficult task, removing the starter motor. Clearly Suzuki never considered that a starter motor may go wrong and need replacing as it is in one of the most in-accessible places. First of all check that you have disconnected the battery. Laying under the car reach up the drivers side of the engine and unbolt the two bolts holding the motor in place and easy it back. There is no need to remove it completely and no need to undo all the cables attached to in.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 15. Starter Motor (from underneath car).png|thumb|left|250px|Figure 15. Starter Motor (from underneath car)]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
We are nearly there now. Remove plastic clutch housing cap and prise the end of the clutch cable from clutch release fork. Then undo the two bolts holding the clutch cable to the transmission and withdraw the clutch cable assembly. Also remove the small tin-plate on the bottom front of the clutch housing held on by a pair of small 10mm bolts.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 16. Clutch cable (unhooked).png|thumb|left|250px|Figure 16. Clutch cable (unhooked)]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
The official workshop manual now says to undo the bellhousing bolts and lower the gearbox away from the engine. Whoever wrote this must have been smoking something very exotic. The first problem is to locate all the bolts on the bellhousing as they are well hidden. Take a close look at the picture below and locate all the bolts.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 17. Gearbox bolts.png|thumb|left|250px|Figure 17. Gearbox bolts]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
The next problem is undoing them as there is no room to get a socket set in. I had to use a complex combination of extensions and flex joints from two socket sets to get to a couple of the bolts. Also note that there is very little chance of the gearbox falling off once the bolts are undone so don’t spend a lot of time supporting it.&lt;br /&gt;
&lt;br /&gt;
Separating the gearbox from the engine can be a real pain (literally). The gearbox is located on studs and corrosion can hold it in place. I had to hit the bellhousing edge with a large hammer (protecting the metal with a wooden block) before it would separate.&lt;br /&gt;
&lt;br /&gt;
Once it is separated you have to drop the gearbox down. The transmission tunnel is so tight that this appears to be a near impossible task. I had to jack the engine forward to gain as much room as possible. You will also find that the gearbox will move backwards a little way in the tunnel, this means you can then open a useful gap around the clutch.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 18. Pulling the engine forward with strap.png|thumb|left|250px|Figure 18. Pulling the engine forward with strap]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 19. Gap between gearbox and clutch with engine pulled forward.png|thumb|left|250px|Figure 19. Gap between gearbox and clutch with engine pulled forward]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Some people have changed the clutch using just this gap. Instead, I undid the clutch cover bolts and removed the clutch assembly with the gearbox still in place. Removing the clutch then meant there was just enough room for the gearbox to be pulled out.&lt;br /&gt;
&lt;br /&gt;
Within the clutch kit should be a new cover, new plate and new release bearing.&lt;br /&gt;
&lt;br /&gt;
The old release bearing is removed by prising the spring clip out of the mounting and sliding it out of the spring. Re-assembly is just as easy, make sure that the splines are lightly greased and the inside of the release bearing where it slides on the shaft is greased (not the bearing itself – this should be lubricated by the factory).&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 20. Clutch Release Bearing.png|thumb|left|250px|Figure 20. Clutch Release Bearing]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Put grease on the moving points of the clutch release arm as well.&lt;br /&gt;
&lt;br /&gt;
The pictures below shows the clutch mechanism. I purchased a cheap kit (CPK1086) from ebay. The quality seems ok (it is stamped as being made by AISIN – who supply Suzuki with parts), the only issue being that it was supplied with the incorrect release bearing. The company immediately shipped the correct bearing free of charge and assured me that the correct bearing should have been in the kit. Also note that the new plate has 4 springs whilst the old one has 3, again I have been assured that this is ok.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 21. Wrong Release Bearing is on Right.png|thumb|left|250px|Figure 21. Wrong Release Bearing is on Right]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 22. New Clutch Plate on left.png|thumb|left|250px|Figure 22. New Clutch Plate on left]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 23. New clutch cover on left.png|thumb|left|250px|Figure 23. New clutch cover on left]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Assemble the new clutch mechanism using a clutch alignment tool (I got mine cheap - £1 – as it was a girlie pink colour and had remained unsold in the shop for a long time). With this tool you assemble the clutch off the car and then lift the whole unit into place and bolt down the clutch cover to the flywheel. Remove clutch alignment tool.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 24. Clutch Assembled.png|thumb|left|250px|Figure 24. Clutch Assembled]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 25. Clutch with alignment tool.png|thumb|left|250px|Figure 25. Clutch with alignment tool]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 26. Clutch back in place.png|thumb|left|250px|Figure 26. Clutch back in place]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Wipe a layer of grease around the mating face of the gearbox, this should mean it doesn’t stick in the future and should make it easier to re-assemble.&lt;/div&gt;</summary>
		<author><name>Leftcase</name></author>
	</entry>
	<entry>
		<id>https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_28_-_clutch_back_in_place.png&amp;diff=629</id>
		<title>File:Clutch replacement guide - figure 28 - clutch back in place.png</title>
		<link rel="alternate" type="text/html" href="https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_28_-_clutch_back_in_place.png&amp;diff=629"/>
		<updated>2016-06-03T20:03:52Z</updated>

		<summary type="html">&lt;p&gt;Leftcase: &lt;/p&gt;
&lt;hr /&gt;
&lt;div&gt;&lt;/div&gt;</summary>
		<author><name>Leftcase</name></author>
	</entry>
	<entry>
		<id>https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_27_-_clutch_with_alignment_tool.png&amp;diff=628</id>
		<title>File:Clutch replacement guide - figure 27 - clutch with alignment tool.png</title>
		<link rel="alternate" type="text/html" href="https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_27_-_clutch_with_alignment_tool.png&amp;diff=628"/>
		<updated>2016-06-03T20:03:06Z</updated>

		<summary type="html">&lt;p&gt;Leftcase: &lt;/p&gt;
&lt;hr /&gt;
&lt;div&gt;&lt;/div&gt;</summary>
		<author><name>Leftcase</name></author>
	</entry>
	<entry>
		<id>https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_26_-_clutch_assembled.png&amp;diff=627</id>
		<title>File:Clutch replacement guide - figure 26 - clutch assembled.png</title>
		<link rel="alternate" type="text/html" href="https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_26_-_clutch_assembled.png&amp;diff=627"/>
		<updated>2016-06-03T20:02:17Z</updated>

		<summary type="html">&lt;p&gt;Leftcase: &lt;/p&gt;
&lt;hr /&gt;
&lt;div&gt;&lt;/div&gt;</summary>
		<author><name>Leftcase</name></author>
	</entry>
	<entry>
		<id>https://www.bigjimny.com/mediawiki/index.php?title=Clutch_replacement&amp;diff=626</id>
		<title>Clutch replacement</title>
		<link rel="alternate" type="text/html" href="https://www.bigjimny.com/mediawiki/index.php?title=Clutch_replacement&amp;diff=626"/>
		<updated>2016-06-03T19:51:55Z</updated>

		<summary type="html">&lt;p&gt;Leftcase: /* A guide to changing the clutch. */&lt;/p&gt;
&lt;hr /&gt;
&lt;div&gt;&lt;br /&gt;
== A guide to changing the clutch. ==&lt;br /&gt;
&lt;br /&gt;
It is inevitable that at some point you will have to face changing the clutch. It dips in and out of the mud on a regular basis as the bell-housing is not sealed. Eventually the clutch thrust bearing will start rattling and the action will become stiff and heavy.&lt;br /&gt;
Changing the clutch on a Jimny seems to be not for the faint hearted. It’s a very physical task and it is not pleasant struggling with the gearbox under the car, it is a very tight fit in the transmission tunnel.&lt;br /&gt;
&lt;br /&gt;
No special tools are required, but a good toolkit is needed. You will need extension bars for a socket set as some of the bolts are well hidden and difficult to access.&lt;br /&gt;
A breaker bar is also needed as some bolts are very tight.&lt;br /&gt;
&lt;br /&gt;
If this hasn’t put you off then its time to start work. It goes without saying that you should jet-wash the underside of the car if possible to remove as much of the muck before it drops on you!&lt;br /&gt;
There are two ways of changing the clutch, one is to take the engine and gearbox out and the other is to drop the gearbox off. The Suzuki factory manual suggests the gearbox dropping method so that is the way I have gone.&lt;br /&gt;
&lt;br /&gt;
The factory manual suggests it is not necessary to remove the transfer box, but I have removed it as you will need all the space you can get, I thoroughly recommend that you also remove the transfer box.&lt;br /&gt;
&lt;br /&gt;
If you have the luxury of a bit of time then spray the visible bolts with WD40 a day or so before. In particular you should try and spray the bolts holding the exhaust front section and the bolts around the gearbox housing as these are difficult.&lt;br /&gt;
&lt;br /&gt;
Starting inside the car it is necessary to remove both the gear lever and the transfer box lever.&lt;br /&gt;
&lt;br /&gt;
To remove the gearbox lever you have to remove the centre console. This is held on by four screws on the side at the front and back.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 1. Removing the Centre Console.png|thumb|left|250px|Figure 1. Removing the Centre Console]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
The console then lifts out. Mine was more of a problem as I have a switch panel fitted so I then needed to remove the gearlever before the console would come completely away, but this has to be done at some point anyway. Pull the gaiter away to reveal the three bolt heads around the base of the gearlever, undo the bolts and carefully lift out the gearstick, note that there is a small spring and a cup that should not be lost!&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 2. Removing the Gearlever.png|thumb|left|250px|Figure 2. Removing the Gearlever]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
With the console removed you will then see a frame that holds in a second gaiter. Simply undo the bolts and lift the frame clear.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 3. Removing the lower Gaiter.png|thumb|left|250px|Figure 3. Removing the lower Gaiter]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
If you are removing the Transfer Box then you need to remove the gaiter etc. around the Transfer Box Level. First locate the small screw at the rear of the transfer knob and remove it.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 4. Removing the Transfer Lever Knob.png|thumb|left|250px|Figure 4. Removing the Transfer Lever Knob]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Unscrew the frame around the gaiter and pull the frame and gaiter clear.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 5. Removing the Transfer Level Gaiter.png|thumb|left|250px|Figure 5. Removing the Transfer Level Gaiter]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Move outside the car and disconnect the negative cable at battery.&lt;br /&gt;
Now drain the oil from the gearbox and transfer box, if you are not doing any work on the transfer box then it is not strictly necessary to drain the oil providing you keep it upright to stop the oil coming out of the lever hole.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 6. Gearbox Drain Plugs.png|thumb|left|250px|Figure 6. Gearbox Drain Plugs]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
On my Jimny the drain plugs are square and therefore the square end of a 3/8 socket driver fits. Always undo the filler plug first because if the filler is stuck you do not want to drain the oil and not be able to fill it again. The gearbox filler is hidden up the side of the gearbox and lack of space is a problem&lt;br /&gt;
&lt;br /&gt;
On the Transfer Box disconnect the 4WD switch wire at coupler and unclamp harness. Then disconnect the speed sensor coupler.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 7. Transfer Box Fillers and Connectors.png|thumb|left|250px|Figure 7. Transfer Box Fillers and Connectors]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Now remove the front section of the exhaust pipe. This is held in place by pairs of springs with bolts inside. Due to the heat and stress the front bolts were really, really difficult to move. So much so I think there is real possibility of shearing them on some cars. There is a pair at the front and a pair at the back.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 8. Exhaust Bolts.png|thumb|left|250px|Figure 8. Exhaust Bolts]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Do not lift the exhaust of the rubber hangers yet. There is a Lambda sensor connected to the top of the catalytic converter.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 9. Lambda Sensor on Converter.png|thumb|left|250px|Figure 9. Lambda Sensor on Converter]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
This needs to be disconnected. The Suzuki manual shows the sensor being unscrewed from the top of the converter. However, the sensor has been subject to red hot heat, water and mud, therefore mine was firmly rusted in. Instead I followed the wiring back up to behind the engine. Just behind the head on the passenger side is a set of connectors, unbolt the connector mounting bracket and prise the Lambda connector apart (this is very stiff as well!).&lt;br /&gt;
&lt;br /&gt;
[[File:Lambda Sensor Connector Behind Here.png|thumb|left|250px|Lambda Sensor Connector Behind Here]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
With the Lambda sensor disconnected you can pull the front exhaust section off the rubber mounts.&lt;br /&gt;
&lt;br /&gt;
Now remove the propshafts. On each shaft paint some marks so they can be rebolted to the flanges in the correct position when you are re-building it. Paint all the flanges and also mark the sliding joint in the front propshaft. Remove the FRONT propshaft FIRST, followed by the Gearbox/Transfer box shaft SECOND. Where possible do the REAR propshaft LAST. Why! – because all the propshaft bolts are quite tight and therefore you need to hold the propshafts in place whilst you try to undo the bolts. As the front hubs are vacuum operated there is no easy way to lock the props if you have disconnected the rear first. With the rear prop still on the rear wheels keep the system locked. I found out this trick the hard way.&lt;br /&gt;
&lt;br /&gt;
[[File:Mark the Propshaft.png|thumb|left|250px|Mark the Propshaft]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Now undo the 3 large mounting nuts on the transfer box mount and the 4 bolts on the mounting flange. Now the transfer box should lift down.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 10. Transfer mounts.png|thumb|left|250px|Figure 10. Transfer mounts]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 11. Transfer Mounts.png|thumb|left|250px|Figure 11. Transfer Mounts]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Now for the complex bit. The Jimny has a remote gearbox mechanism bolted onto the rear of the gearbox and this needs to be removed. It’s probably easier to see the part after it has been removed as it is clearer what you are trying to achieve. Note this is the top view, you will normally be underneath!&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 12. Gearbox Remote Mechanism.png|thumb|left|250px|Figure 12. Gearbox Remote Mechanism]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Remove gear shift control joint bolt and extension rod bolt.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 13. Remote Mechanism in place.png|thumb|left|250px|Figure 13. Remote Mechanism in place]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Remove the Engine Rear Mounting bolts (Three of them, one either side and one in the rubber bit). This is the mount under the gearbox that rests on the chassis crossmember.&lt;br /&gt;
&lt;br /&gt;
Using a long socket extension, reach into the remote mechanism and undo the 4 bolts that connect it to the gearbox. These are hard to reach.&lt;br /&gt;
&lt;br /&gt;
The entire mechanism should then be removeable complete with the mounts. Also unbolt all the other metal bits (including the exhaust mounting rubber) from the rear cross member as you will need to squeeze the Gearbox out later on.&lt;br /&gt;
&lt;br /&gt;
Now remove the reversing light switch. This is on top of the gearbox towards the front and was more accessible from under the bonnet by reaching down the back of the engine on the passenger side (UK). Tie it up out of the way.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 14. Gearbox Reverse Switch.png|thumb|left|250px|Figure 14. Gearbox Reverse Switch]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Now for the next difficult task, removing the starter motor. Clearly Suzuki never considered that a starter motor may go wrong and need replacing as it is in one of the most in-accessible places. First of all check that you have disconnected the battery. Laying under the car reach up the drivers side of the engine and unbolt the two bolts holding the motor in place and easy it back. There is no need to remove it completely and no need to undo all the cables attached to in.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 15. Starter Motor (from underneath car).png|thumb|left|250px|Figure 15. Starter Motor (from underneath car)]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
We are nearly there now. Remove plastic clutch housing cap and prise the end of the clutch cable from clutch release fork. Then undo the two bolts holding the clutch cable to the transmission and withdraw the clutch cable assembly. Also remove the small tin-plate on the bottom front of the clutch housing held on by a pair of small 10mm bolts.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 16. Clutch cable (unhooked).png|thumb|left|250px|Figure 16. Clutch cable (unhooked)]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
The official workshop manual now says to undo the bellhousing bolts and lower the gearbox away from the engine. Whoever wrote this must have been smoking something very exotic. The first problem is to locate all the bolts on the bellhousing as they are well hidden. Take a close look at the picture below and locate all the bolts.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 17. Gearbox bolts.png|thumb|left|250px|Figure 17. Gearbox bolts]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
The next problem is undoing them as there is no room to get a socket set in. I had to use a complex combination of extensions and flex joints from two socket sets to get to a couple of the bolts. Also note that there is very little chance of the gearbox falling off once the bolts are undone so don’t spend a lot of time supporting it.&lt;br /&gt;
&lt;br /&gt;
Separating the gearbox from the engine can be a real pain (literally). The gearbox is located on studs and corrosion can hold it in place. I had to hit the bellhousing edge with a large hammer (protecting the metal with a wooden block) before it would separate.&lt;br /&gt;
&lt;br /&gt;
Once it is separated you have to drop the gearbox down. The transmission tunnel is so tight that this appears to be a near impossible task. I had to jack the engine forward to gain as much room as possible. You will also find that the gearbox will move backwards a little way in the tunnel, this means you can then open a useful gap around the clutch.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 18. Pulling the engine forward with strap.png|thumb|left|250px|Figure 18. Pulling the engine forward with strap]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 19. Gap between gearbox and clutch with engine pulled forward.png|thumb|left|250px|Figure 19. Gap between gearbox and clutch with engine pulled forward]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Some people have changed the clutch using just this gap. Instead, I undid the clutch cover bolts and removed the clutch assembly with the gearbox still in place. Removing the clutch then meant there was just enough room for the gearbox to be pulled out.&lt;br /&gt;
&lt;br /&gt;
Within the clutch kit should be a new cover, new plate and new release bearing.&lt;br /&gt;
&lt;br /&gt;
The old release bearing is removed by prising the spring clip out of the mounting and sliding it out of the spring. Re-assembly is just as easy, make sure that the splines are lightly greased and the inside of the release bearing where it slides on the shaft is greased (not the bearing itself – this should be lubricated by the factory).&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 20. Clutch Release Bearing.png|thumb|left|250px|Figure 20. Clutch Release Bearing]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Put grease on the moving points of the clutch release arm as well.&lt;br /&gt;
&lt;br /&gt;
The pictures below shows the clutch mechanism. I purchased a cheap kit (CPK1086) from ebay. The quality seems ok (it is stamped as being made by AISIN – who supply Suzuki with parts), the only issue being that it was supplied with the incorrect release bearing. The company immediately shipped the correct bearing free of charge and assured me that the correct bearing should have been in the kit. Also note that the new plate has 4 springs whilst the old one has 3, again I have been assured that this is ok.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 21. Wrong Release Bearing is on Right.png|thumb|left|250px|Figure 21. Wrong Release Bearing is on Right]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 22. New Clutch Plate on left.png|thumb|left|250px|Figure 22. New Clutch Plate on left]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 23. New clutch cover on left.png|thumb|left|250px|Figure 23. New clutch cover on left]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Assemble the new clutch mechanism using a clutch alignment tool (I got mine cheap - £1 – as it was a girlie pink colour and had remained unsold in the shop for a long time). With this tool you assemble the clutch off the car and then lift the whole unit into place and bolt down the clutch cover to the flywheel. Remove clutch alignment tool.&lt;/div&gt;</summary>
		<author><name>Leftcase</name></author>
	</entry>
	<entry>
		<id>https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_25_-_new_clutch_cover_on_left.png&amp;diff=625</id>
		<title>File:Clutch replacement guide - figure 25 - new clutch cover on left.png</title>
		<link rel="alternate" type="text/html" href="https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_25_-_new_clutch_cover_on_left.png&amp;diff=625"/>
		<updated>2016-06-03T19:50:05Z</updated>

		<summary type="html">&lt;p&gt;Leftcase: &lt;/p&gt;
&lt;hr /&gt;
&lt;div&gt;&lt;/div&gt;</summary>
		<author><name>Leftcase</name></author>
	</entry>
	<entry>
		<id>https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_24_-_new_clutch_plate_on_left.png&amp;diff=624</id>
		<title>File:Clutch replacement guide - figure 24 - new clutch plate on left.png</title>
		<link rel="alternate" type="text/html" href="https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_24_-_new_clutch_plate_on_left.png&amp;diff=624"/>
		<updated>2016-06-03T19:49:46Z</updated>

		<summary type="html">&lt;p&gt;Leftcase: &lt;/p&gt;
&lt;hr /&gt;
&lt;div&gt;&lt;/div&gt;</summary>
		<author><name>Leftcase</name></author>
	</entry>
	<entry>
		<id>https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_23_-_wrong_release_bearing_is_on_right.png&amp;diff=623</id>
		<title>File:Clutch replacement guide - figure 23 - wrong release bearing is on right.png</title>
		<link rel="alternate" type="text/html" href="https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_23_-_wrong_release_bearing_is_on_right.png&amp;diff=623"/>
		<updated>2016-06-03T19:48:02Z</updated>

		<summary type="html">&lt;p&gt;Leftcase: &lt;/p&gt;
&lt;hr /&gt;
&lt;div&gt;&lt;/div&gt;</summary>
		<author><name>Leftcase</name></author>
	</entry>
	<entry>
		<id>https://www.bigjimny.com/mediawiki/index.php?title=Clutch_replacement&amp;diff=622</id>
		<title>Clutch replacement</title>
		<link rel="alternate" type="text/html" href="https://www.bigjimny.com/mediawiki/index.php?title=Clutch_replacement&amp;diff=622"/>
		<updated>2016-06-03T19:46:22Z</updated>

		<summary type="html">&lt;p&gt;Leftcase: &lt;/p&gt;
&lt;hr /&gt;
&lt;div&gt;&lt;br /&gt;
== A guide to changing the clutch. ==&lt;br /&gt;
&lt;br /&gt;
It is inevitable that at some point you will have to face changing the clutch. It dips in and out of the mud on a regular basis as the bell-housing is not sealed. Eventually the clutch thrust bearing will start rattling and the action will become stiff and heavy.&lt;br /&gt;
Changing the clutch on a Jimny seems to be not for the faint hearted. It’s a very physical task and it is not pleasant struggling with the gearbox under the car, it is a very tight fit in the transmission tunnel.&lt;br /&gt;
&lt;br /&gt;
No special tools are required, but a good toolkit is needed. You will need extension bars for a socket set as some of the bolts are well hidden and difficult to access.&lt;br /&gt;
A breaker bar is also needed as some bolts are very tight.&lt;br /&gt;
&lt;br /&gt;
If this hasn’t put you off then its time to start work. It goes without saying that you should jet-wash the underside of the car if possible to remove as much of the muck before it drops on you!&lt;br /&gt;
There are two ways of changing the clutch, one is to take the engine and gearbox out and the other is to drop the gearbox off. The Suzuki factory manual suggests the gearbox dropping method so that is the way I have gone.&lt;br /&gt;
&lt;br /&gt;
The factory manual suggests it is not necessary to remove the transfer box, but I have removed it as you will need all the space you can get, I thoroughly recommend that you also remove the transfer box.&lt;br /&gt;
&lt;br /&gt;
If you have the luxury of a bit of time then spray the visible bolts with WD40 a day or so before. In particular you should try and spray the bolts holding the exhaust front section and the bolts around the gearbox housing as these are difficult.&lt;br /&gt;
&lt;br /&gt;
Starting inside the car it is necessary to remove both the gear lever and the transfer box lever.&lt;br /&gt;
&lt;br /&gt;
To remove the gearbox lever you have to remove the centre console. This is held on by four screws on the side at the front and back.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 1. Removing the Centre Console.png|thumb|left|250px|Figure 1. Removing the Centre Console]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
The console then lifts out. Mine was more of a problem as I have a switch panel fitted so I then needed to remove the gearlever before the console would come completely away, but this has to be done at some point anyway. Pull the gaiter away to reveal the three bolt heads around the base of the gearlever, undo the bolts and carefully lift out the gearstick, note that there is a small spring and a cup that should not be lost!&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 2. Removing the Gearlever.png|thumb|left|250px|Figure 2. Removing the Gearlever]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
With the console removed you will then see a frame that holds in a second gaiter. Simply undo the bolts and lift the frame clear.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 3. Removing the lower Gaiter.png|thumb|left|250px|Figure 3. Removing the lower Gaiter]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
If you are removing the Transfer Box then you need to remove the gaiter etc. around the Transfer Box Level. First locate the small screw at the rear of the transfer knob and remove it.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 4. Removing the Transfer Lever Knob.png|thumb|left|250px|Figure 4. Removing the Transfer Lever Knob]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Unscrew the frame around the gaiter and pull the frame and gaiter clear.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 5. Removing the Transfer Level Gaiter.png|thumb|left|250px|Figure 5. Removing the Transfer Level Gaiter]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Move outside the car and disconnect the negative cable at battery.&lt;br /&gt;
Now drain the oil from the gearbox and transfer box, if you are not doing any work on the transfer box then it is not strictly necessary to drain the oil providing you keep it upright to stop the oil coming out of the lever hole.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 6. Gearbox Drain Plugs.png|thumb|left|250px|Figure 6. Gearbox Drain Plugs]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
On my Jimny the drain plugs are square and therefore the square end of a 3/8 socket driver fits. Always undo the filler plug first because if the filler is stuck you do not want to drain the oil and not be able to fill it again. The gearbox filler is hidden up the side of the gearbox and lack of space is a problem&lt;br /&gt;
&lt;br /&gt;
On the Transfer Box disconnect the 4WD switch wire at coupler and unclamp harness. Then disconnect the speed sensor coupler.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 7. Transfer Box Fillers and Connectors.png|thumb|left|250px|Figure 7. Transfer Box Fillers and Connectors]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Now remove the front section of the exhaust pipe. This is held in place by pairs of springs with bolts inside. Due to the heat and stress the front bolts were really, really difficult to move. So much so I think there is real possibility of shearing them on some cars. There is a pair at the front and a pair at the back.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 8. Exhaust Bolts.png|thumb|left|250px|Figure 8. Exhaust Bolts]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Do not lift the exhaust of the rubber hangers yet. There is a Lambda sensor connected to the top of the catalytic converter.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 9. Lambda Sensor on Converter.png|thumb|left|250px|Figure 9. Lambda Sensor on Converter]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
This needs to be disconnected. The Suzuki manual shows the sensor being unscrewed from the top of the converter. However, the sensor has been subject to red hot heat, water and mud, therefore mine was firmly rusted in. Instead I followed the wiring back up to behind the engine. Just behind the head on the passenger side is a set of connectors, unbolt the connector mounting bracket and prise the Lambda connector apart (this is very stiff as well!).&lt;br /&gt;
&lt;br /&gt;
[[File:Lambda Sensor Connector Behind Here.png|thumb|left|250px|Lambda Sensor Connector Behind Here]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
With the Lambda sensor disconnected you can pull the front exhaust section off the rubber mounts.&lt;br /&gt;
&lt;br /&gt;
Now remove the propshafts. On each shaft paint some marks so they can be rebolted to the flanges in the correct position when you are re-building it. Paint all the flanges and also mark the sliding joint in the front propshaft. Remove the FRONT propshaft FIRST, followed by the Gearbox/Transfer box shaft SECOND. Where possible do the REAR propshaft LAST. Why! – because all the propshaft bolts are quite tight and therefore you need to hold the propshafts in place whilst you try to undo the bolts. As the front hubs are vacuum operated there is no easy way to lock the props if you have disconnected the rear first. With the rear prop still on the rear wheels keep the system locked. I found out this trick the hard way.&lt;br /&gt;
&lt;br /&gt;
[[File:Mark the Propshaft.png|thumb|left|250px|Mark the Propshaft]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Now undo the 3 large mounting nuts on the transfer box mount and the 4 bolts on the mounting flange. Now the transfer box should lift down.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 10. Transfer mounts.png|thumb|left|250px|Figure 10. Transfer mounts]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 11. Transfer Mounts.png|thumb|left|250px|Figure 11. Transfer Mounts]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Now for the complex bit. The Jimny has a remote gearbox mechanism bolted onto the rear of the gearbox and this needs to be removed. It’s probably easier to see the part after it has been removed as it is clearer what you are trying to achieve. Note this is the top view, you will normally be underneath!&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 12. Gearbox Remote Mechanism.png|thumb|left|250px|Figure 12. Gearbox Remote Mechanism]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Remove gear shift control joint bolt and extension rod bolt.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 13. Remote Mechanism in place.png|thumb|left|250px|Figure 13. Remote Mechanism in place]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Remove the Engine Rear Mounting bolts (Three of them, one either side and one in the rubber bit). This is the mount under the gearbox that rests on the chassis crossmember.&lt;br /&gt;
&lt;br /&gt;
Using a long socket extension, reach into the remote mechanism and undo the 4 bolts that connect it to the gearbox. These are hard to reach.&lt;br /&gt;
&lt;br /&gt;
The entire mechanism should then be removeable complete with the mounts. Also unbolt all the other metal bits (including the exhaust mounting rubber) from the rear cross member as you will need to squeeze the Gearbox out later on.&lt;br /&gt;
&lt;br /&gt;
Now remove the reversing light switch. This is on top of the gearbox towards the front and was more accessible from under the bonnet by reaching down the back of the engine on the passenger side (UK). Tie it up out of the way.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 14. Gearbox Reverse Switch.png|thumb|left|250px|Figure 14. Gearbox Reverse Switch]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Now for the next difficult task, removing the starter motor. Clearly Suzuki never considered that a starter motor may go wrong and need replacing as it is in one of the most in-accessible places. First of all check that you have disconnected the battery. Laying under the car reach up the drivers side of the engine and unbolt the two bolts holding the motor in place and easy it back. There is no need to remove it completely and no need to undo all the cables attached to in.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 15. Starter Motor (from underneath car).png|thumb|left|250px|Figure 15. Starter Motor (from underneath car)]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
We are nearly there now. Remove plastic clutch housing cap and prise the end of the clutch cable from clutch release fork. Then undo the two bolts holding the clutch cable to the transmission and withdraw the clutch cable assembly. Also remove the small tin-plate on the bottom front of the clutch housing held on by a pair of small 10mm bolts.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 16. Clutch cable (unhooked).png|thumb|left|250px|Figure 16. Clutch cable (unhooked)]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
The official workshop manual now says to undo the bellhousing bolts and lower the gearbox away from the engine. Whoever wrote this must have been smoking something very exotic. The first problem is to locate all the bolts on the bellhousing as they are well hidden. Take a close look at the picture below and locate all the bolts.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 17. Gearbox bolts.png|thumb|left|250px|Figure 17. Gearbox bolts]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
The next problem is undoing them as there is no room to get a socket set in. I had to use a complex combination of extensions and flex joints from two socket sets to get to a couple of the bolts. Also note that there is very little chance of the gearbox falling off once the bolts are undone so don’t spend a lot of time supporting it.&lt;br /&gt;
&lt;br /&gt;
Separating the gearbox from the engine can be a real pain (literally). The gearbox is located on studs and corrosion can hold it in place. I had to hit the bellhousing edge with a large hammer (protecting the metal with a wooden block) before it would separate.&lt;br /&gt;
&lt;br /&gt;
Once it is separated you have to drop the gearbox down. The transmission tunnel is so tight that this appears to be a near impossible task. I had to jack the engine forward to gain as much room as possible. You will also find that the gearbox will move backwards a little way in the tunnel, this means you can then open a useful gap around the clutch.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 18. Pulling the engine forward with strap.png|thumb|left|250px|Figure 18. Pulling the engine forward with strap]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 19. Gap between gearbox and clutch with engine pulled forward.png|thumb|left|250px|Figure 19. Gap between gearbox and clutch with engine pulled forward]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Some people have changed the clutch using just this gap. Instead, I undid the clutch cover bolts and removed the clutch assembly with the gearbox still in place. Removing the clutch then meant there was just enough room for the gearbox to be pulled out.&lt;br /&gt;
&lt;br /&gt;
Within the clutch kit should be a new cover, new plate and new release bearing.&lt;br /&gt;
&lt;br /&gt;
The old release bearing is removed by prising the spring clip out of the mounting and sliding it out of the spring. Re-assembly is just as easy, make sure that the splines are lightly greased and the inside of the release bearing where it slides on the shaft is greased (not the bearing itself – this should be lubricated by the factory).&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 20. Clutch Release Bearing.png|thumb|left|250px|Figure 20. Clutch Release Bearing]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;/div&gt;</summary>
		<author><name>Leftcase</name></author>
	</entry>
	<entry>
		<id>https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_22_-_clutch_release_bearing.png&amp;diff=621</id>
		<title>File:Clutch replacement guide - figure 22 - clutch release bearing.png</title>
		<link rel="alternate" type="text/html" href="https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_22_-_clutch_release_bearing.png&amp;diff=621"/>
		<updated>2016-06-03T19:45:54Z</updated>

		<summary type="html">&lt;p&gt;Leftcase: &lt;/p&gt;
&lt;hr /&gt;
&lt;div&gt;&lt;/div&gt;</summary>
		<author><name>Leftcase</name></author>
	</entry>
	<entry>
		<id>https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_21_-_gap_between_gear_box_and_clutch_with_engine_pulled_forward.png&amp;diff=620</id>
		<title>File:Clutch replacement guide - figure 21 - gap between gear box and clutch with engine pulled forward.png</title>
		<link rel="alternate" type="text/html" href="https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_21_-_gap_between_gear_box_and_clutch_with_engine_pulled_forward.png&amp;diff=620"/>
		<updated>2016-06-03T19:43:27Z</updated>

		<summary type="html">&lt;p&gt;Leftcase: &lt;/p&gt;
&lt;hr /&gt;
&lt;div&gt;&lt;/div&gt;</summary>
		<author><name>Leftcase</name></author>
	</entry>
	<entry>
		<id>https://www.bigjimny.com/mediawiki/index.php?title=Clutch_replacement&amp;diff=619</id>
		<title>Clutch replacement</title>
		<link rel="alternate" type="text/html" href="https://www.bigjimny.com/mediawiki/index.php?title=Clutch_replacement&amp;diff=619"/>
		<updated>2016-06-03T19:40:53Z</updated>

		<summary type="html">&lt;p&gt;Leftcase: &lt;/p&gt;
&lt;hr /&gt;
&lt;div&gt;&lt;br /&gt;
== A guide to changing the clutch. ==&lt;br /&gt;
&lt;br /&gt;
It is inevitable that at some point you will have to face changing the clutch. It dips in and out of the mud on a regular basis as the bell-housing is not sealed. Eventually the clutch thrust bearing will start rattling and the action will become stiff and heavy.&lt;br /&gt;
Changing the clutch on a Jimny seems to be not for the faint hearted. It’s a very physical task and it is not pleasant struggling with the gearbox under the car, it is a very tight fit in the transmission tunnel.&lt;br /&gt;
&lt;br /&gt;
No special tools are required, but a good toolkit is needed. You will need extension bars for a socket set as some of the bolts are well hidden and difficult to access.&lt;br /&gt;
A breaker bar is also needed as some bolts are very tight.&lt;br /&gt;
&lt;br /&gt;
If this hasn’t put you off then its time to start work. It goes without saying that you should jet-wash the underside of the car if possible to remove as much of the muck before it drops on you!&lt;br /&gt;
There are two ways of changing the clutch, one is to take the engine and gearbox out and the other is to drop the gearbox off. The Suzuki factory manual suggests the gearbox dropping method so that is the way I have gone.&lt;br /&gt;
&lt;br /&gt;
The factory manual suggests it is not necessary to remove the transfer box, but I have removed it as you will need all the space you can get, I thoroughly recommend that you also remove the transfer box.&lt;br /&gt;
&lt;br /&gt;
If you have the luxury of a bit of time then spray the visible bolts with WD40 a day or so before. In particular you should try and spray the bolts holding the exhaust front section and the bolts around the gearbox housing as these are difficult.&lt;br /&gt;
&lt;br /&gt;
Starting inside the car it is necessary to remove both the gear lever and the transfer box lever.&lt;br /&gt;
&lt;br /&gt;
To remove the gearbox lever you have to remove the centre console. This is held on by four screws on the side at the front and back.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 1. Removing the Centre Console.png|thumb|left|250px|Figure 1. Removing the Centre Console]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
The console then lifts out. Mine was more of a problem as I have a switch panel fitted so I then needed to remove the gearlever before the console would come completely away, but this has to be done at some point anyway. Pull the gaiter away to reveal the three bolt heads around the base of the gearlever, undo the bolts and carefully lift out the gearstick, note that there is a small spring and a cup that should not be lost!&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 2. Removing the Gearlever.png|thumb|left|250px|Figure 2. Removing the Gearlever]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
With the console removed you will then see a frame that holds in a second gaiter. Simply undo the bolts and lift the frame clear.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 3. Removing the lower Gaiter.png|thumb|left|250px|Figure 3. Removing the lower Gaiter]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
If you are removing the Transfer Box then you need to remove the gaiter etc. around the Transfer Box Level. First locate the small screw at the rear of the transfer knob and remove it.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 4. Removing the Transfer Lever Knob.png|thumb|left|250px|Figure 4. Removing the Transfer Lever Knob]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Unscrew the frame around the gaiter and pull the frame and gaiter clear.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 5. Removing the Transfer Level Gaiter.png|thumb|left|250px|Figure 5. Removing the Transfer Level Gaiter]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Move outside the car and disconnect the negative cable at battery.&lt;br /&gt;
Now drain the oil from the gearbox and transfer box, if you are not doing any work on the transfer box then it is not strictly necessary to drain the oil providing you keep it upright to stop the oil coming out of the lever hole.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 6. Gearbox Drain Plugs.png|thumb|left|250px|Figure 6. Gearbox Drain Plugs]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
On my Jimny the drain plugs are square and therefore the square end of a 3/8 socket driver fits. Always undo the filler plug first because if the filler is stuck you do not want to drain the oil and not be able to fill it again. The gearbox filler is hidden up the side of the gearbox and lack of space is a problem&lt;br /&gt;
&lt;br /&gt;
On the Transfer Box disconnect the 4WD switch wire at coupler and unclamp harness. Then disconnect the speed sensor coupler.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 7. Transfer Box Fillers and Connectors.png|thumb|left|250px|Figure 7. Transfer Box Fillers and Connectors]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Now remove the front section of the exhaust pipe. This is held in place by pairs of springs with bolts inside. Due to the heat and stress the front bolts were really, really difficult to move. So much so I think there is real possibility of shearing them on some cars. There is a pair at the front and a pair at the back.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 8. Exhaust Bolts.png|thumb|left|250px|Figure 8. Exhaust Bolts]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Do not lift the exhaust of the rubber hangers yet. There is a Lambda sensor connected to the top of the catalytic converter.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 9. Lambda Sensor on Converter.png|thumb|left|250px|Figure 9. Lambda Sensor on Converter]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
This needs to be disconnected. The Suzuki manual shows the sensor being unscrewed from the top of the converter. However, the sensor has been subject to red hot heat, water and mud, therefore mine was firmly rusted in. Instead I followed the wiring back up to behind the engine. Just behind the head on the passenger side is a set of connectors, unbolt the connector mounting bracket and prise the Lambda connector apart (this is very stiff as well!).&lt;br /&gt;
&lt;br /&gt;
[[File:Lambda Sensor Connector Behind Here.png|thumb|left|250px|Lambda Sensor Connector Behind Here]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
With the Lambda sensor disconnected you can pull the front exhaust section off the rubber mounts.&lt;br /&gt;
&lt;br /&gt;
Now remove the propshafts. On each shaft paint some marks so they can be rebolted to the flanges in the correct position when you are re-building it. Paint all the flanges and also mark the sliding joint in the front propshaft. Remove the FRONT propshaft FIRST, followed by the Gearbox/Transfer box shaft SECOND. Where possible do the REAR propshaft LAST. Why! – because all the propshaft bolts are quite tight and therefore you need to hold the propshafts in place whilst you try to undo the bolts. As the front hubs are vacuum operated there is no easy way to lock the props if you have disconnected the rear first. With the rear prop still on the rear wheels keep the system locked. I found out this trick the hard way.&lt;br /&gt;
&lt;br /&gt;
[[File:Mark the Propshaft.png|thumb|left|250px|Mark the Propshaft]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Now undo the 3 large mounting nuts on the transfer box mount and the 4 bolts on the mounting flange. Now the transfer box should lift down.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 10. Transfer mounts.png|thumb|left|250px|Figure 10. Transfer mounts]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 11. Transfer Mounts.png|thumb|left|250px|Figure 11. Transfer Mounts]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Now for the complex bit. The Jimny has a remote gearbox mechanism bolted onto the rear of the gearbox and this needs to be removed. It’s probably easier to see the part after it has been removed as it is clearer what you are trying to achieve. Note this is the top view, you will normally be underneath!&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 12. Gearbox Remote Mechanism.png|thumb|left|250px|Figure 12. Gearbox Remote Mechanism]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Remove gear shift control joint bolt and extension rod bolt.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 13. Remote Mechanism in place.png|thumb|left|250px|Figure 13. Remote Mechanism in place]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Remove the Engine Rear Mounting bolts (Three of them, one either side and one in the rubber bit). This is the mount under the gearbox that rests on the chassis crossmember.&lt;br /&gt;
&lt;br /&gt;
Using a long socket extension, reach into the remote mechanism and undo the 4 bolts that connect it to the gearbox. These are hard to reach.&lt;br /&gt;
&lt;br /&gt;
The entire mechanism should then be removeable complete with the mounts. Also unbolt all the other metal bits (including the exhaust mounting rubber) from the rear cross member as you will need to squeeze the Gearbox out later on.&lt;br /&gt;
&lt;br /&gt;
Now remove the reversing light switch. This is on top of the gearbox towards the front and was more accessible from under the bonnet by reaching down the back of the engine on the passenger side (UK). Tie it up out of the way.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 14. Gearbox Reverse Switch.png|thumb|left|250px|Figure 14. Gearbox Reverse Switch]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Now for the next difficult task, removing the starter motor. Clearly Suzuki never considered that a starter motor may go wrong and need replacing as it is in one of the most in-accessible places. First of all check that you have disconnected the battery. Laying under the car reach up the drivers side of the engine and unbolt the two bolts holding the motor in place and easy it back. There is no need to remove it completely and no need to undo all the cables attached to in.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 15. Starter Motor (from underneath car).png|thumb|left|250px|Figure 15. Starter Motor (from underneath car)]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
We are nearly there now. Remove plastic clutch housing cap and prise the end of the clutch cable from clutch release fork. Then undo the two bolts holding the clutch cable to the transmission and withdraw the clutch cable assembly. Also remove the small tin-plate on the bottom front of the clutch housing held on by a pair of small 10mm bolts.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 16. Clutch cable (unhooked).png|thumb|left|250px|Figure 16. Clutch cable (unhooked)]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
The official workshop manual now says to undo the bellhousing bolts and lower the gearbox away from the engine. Whoever wrote this must have been smoking something very exotic. The first problem is to locate all the bolts on the bellhousing as they are well hidden. Take a close look at the picture below and locate all the bolts.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 17. Gearbox bolts.png|thumb|left|250px|Figure 17. Gearbox bolts]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
The next problem is undoing them as there is no room to get a socket set in. I had to use a complex combination of extensions and flex joints from two socket sets to get to a couple of the bolts. Also note that there is very little chance of the gearbox falling off once the bolts are undone so don’t spend a lot of time supporting it.&lt;br /&gt;
&lt;br /&gt;
Separating the gearbox from the engine can be a real pain (literally). The gearbox is located on studs and corrosion can hold it in place. I had to hit the bellhousing edge with a large hammer (protecting the metal with a wooden block) before it would separate.&lt;br /&gt;
&lt;br /&gt;
Once it is separated you have to drop the gearbox down. The transmission tunnel is so tight that this appears to be a near impossible task. I had to jack the engine forward to gain as much room as possible. You will also find that the gearbox will move backwards a little way in the tunnel, this means you can then open a useful gap around the clutch.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 18. Pulling the engine forward with strap.png|thumb|left|250px|Figure 18. Pulling the engine forward with strap]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;/div&gt;</summary>
		<author><name>Leftcase</name></author>
	</entry>
	<entry>
		<id>https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_20_-_pulling_the_engine_forward_with_strap.png&amp;diff=618</id>
		<title>File:Clutch replacement guide - figure 20 - pulling the engine forward with strap.png</title>
		<link rel="alternate" type="text/html" href="https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_20_-_pulling_the_engine_forward_with_strap.png&amp;diff=618"/>
		<updated>2016-06-03T19:40:31Z</updated>

		<summary type="html">&lt;p&gt;Leftcase: &lt;/p&gt;
&lt;hr /&gt;
&lt;div&gt;&lt;/div&gt;</summary>
		<author><name>Leftcase</name></author>
	</entry>
	<entry>
		<id>https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_19_-_gear_box_bolts.png&amp;diff=617</id>
		<title>File:Clutch replacement guide - figure 19 - gear box bolts.png</title>
		<link rel="alternate" type="text/html" href="https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_19_-_gear_box_bolts.png&amp;diff=617"/>
		<updated>2016-06-03T19:38:23Z</updated>

		<summary type="html">&lt;p&gt;Leftcase: &lt;/p&gt;
&lt;hr /&gt;
&lt;div&gt;&lt;/div&gt;</summary>
		<author><name>Leftcase</name></author>
	</entry>
	<entry>
		<id>https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_18_-_clutch_cable_(unhooked).png&amp;diff=616</id>
		<title>File:Clutch replacement guide - figure 18 - clutch cable (unhooked).png</title>
		<link rel="alternate" type="text/html" href="https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_18_-_clutch_cable_(unhooked).png&amp;diff=616"/>
		<updated>2016-06-03T19:36:48Z</updated>

		<summary type="html">&lt;p&gt;Leftcase: &lt;/p&gt;
&lt;hr /&gt;
&lt;div&gt;&lt;/div&gt;</summary>
		<author><name>Leftcase</name></author>
	</entry>
	<entry>
		<id>https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_17_-_starter_motor_(from_underneath_car).png&amp;diff=615</id>
		<title>File:Clutch replacement guide - figure 17 - starter motor (from underneath car).png</title>
		<link rel="alternate" type="text/html" href="https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_17_-_starter_motor_(from_underneath_car).png&amp;diff=615"/>
		<updated>2016-06-03T19:34:37Z</updated>

		<summary type="html">&lt;p&gt;Leftcase: &lt;/p&gt;
&lt;hr /&gt;
&lt;div&gt;&lt;/div&gt;</summary>
		<author><name>Leftcase</name></author>
	</entry>
	<entry>
		<id>https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_16_-_gear_box_reverse_switch.png&amp;diff=614</id>
		<title>File:Clutch replacement guide - figure 16 - gear box reverse switch.png</title>
		<link rel="alternate" type="text/html" href="https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_16_-_gear_box_reverse_switch.png&amp;diff=614"/>
		<updated>2016-06-03T19:32:17Z</updated>

		<summary type="html">&lt;p&gt;Leftcase: &lt;/p&gt;
&lt;hr /&gt;
&lt;div&gt;&lt;/div&gt;</summary>
		<author><name>Leftcase</name></author>
	</entry>
	<entry>
		<id>https://www.bigjimny.com/mediawiki/index.php?title=Clutch_replacement&amp;diff=613</id>
		<title>Clutch replacement</title>
		<link rel="alternate" type="text/html" href="https://www.bigjimny.com/mediawiki/index.php?title=Clutch_replacement&amp;diff=613"/>
		<updated>2016-06-03T19:30:17Z</updated>

		<summary type="html">&lt;p&gt;Leftcase: &lt;/p&gt;
&lt;hr /&gt;
&lt;div&gt;&lt;br /&gt;
== A guide to changing the clutch. ==&lt;br /&gt;
&lt;br /&gt;
It is inevitable that at some point you will have to face changing the clutch. It dips in and out of the mud on a regular basis as the bell-housing is not sealed. Eventually the clutch thrust bearing will start rattling and the action will become stiff and heavy.&lt;br /&gt;
Changing the clutch on a Jimny seems to be not for the faint hearted. It’s a very physical task and it is not pleasant struggling with the gearbox under the car, it is a very tight fit in the transmission tunnel.&lt;br /&gt;
&lt;br /&gt;
No special tools are required, but a good toolkit is needed. You will need extension bars for a socket set as some of the bolts are well hidden and difficult to access.&lt;br /&gt;
A breaker bar is also needed as some bolts are very tight.&lt;br /&gt;
&lt;br /&gt;
If this hasn’t put you off then its time to start work. It goes without saying that you should jet-wash the underside of the car if possible to remove as much of the muck before it drops on you!&lt;br /&gt;
There are two ways of changing the clutch, one is to take the engine and gearbox out and the other is to drop the gearbox off. The Suzuki factory manual suggests the gearbox dropping method so that is the way I have gone.&lt;br /&gt;
&lt;br /&gt;
The factory manual suggests it is not necessary to remove the transfer box, but I have removed it as you will need all the space you can get, I thoroughly recommend that you also remove the transfer box.&lt;br /&gt;
&lt;br /&gt;
If you have the luxury of a bit of time then spray the visible bolts with WD40 a day or so before. In particular you should try and spray the bolts holding the exhaust front section and the bolts around the gearbox housing as these are difficult.&lt;br /&gt;
&lt;br /&gt;
Starting inside the car it is necessary to remove both the gear lever and the transfer box lever.&lt;br /&gt;
&lt;br /&gt;
To remove the gearbox lever you have to remove the centre console. This is held on by four screws on the side at the front and back.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 1. Removing the Centre Console.png|thumb|left|250px|Figure 1. Removing the Centre Console]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
The console then lifts out. Mine was more of a problem as I have a switch panel fitted so I then needed to remove the gearlever before the console would come completely away, but this has to be done at some point anyway. Pull the gaiter away to reveal the three bolt heads around the base of the gearlever, undo the bolts and carefully lift out the gearstick, note that there is a small spring and a cup that should not be lost!&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 2. Removing the Gearlever.png|thumb|left|250px|Figure 2. Removing the Gearlever]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
With the console removed you will then see a frame that holds in a second gaiter. Simply undo the bolts and lift the frame clear.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 3. Removing the lower Gaiter.png|thumb|left|250px|Figure 3. Removing the lower Gaiter]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
If you are removing the Transfer Box then you need to remove the gaiter etc. around the Transfer Box Level. First locate the small screw at the rear of the transfer knob and remove it.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 4. Removing the Transfer Lever Knob.png|thumb|left|250px|Figure 4. Removing the Transfer Lever Knob]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Unscrew the frame around the gaiter and pull the frame and gaiter clear.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 5. Removing the Transfer Level Gaiter.png|thumb|left|250px|Figure 5. Removing the Transfer Level Gaiter]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Move outside the car and disconnect the negative cable at battery.&lt;br /&gt;
Now drain the oil from the gearbox and transfer box, if you are not doing any work on the transfer box then it is not strictly necessary to drain the oil providing you keep it upright to stop the oil coming out of the lever hole.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 6. Gearbox Drain Plugs.png|thumb|left|250px|Figure 6. Gearbox Drain Plugs]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
On my Jimny the drain plugs are square and therefore the square end of a 3/8 socket driver fits. Always undo the filler plug first because if the filler is stuck you do not want to drain the oil and not be able to fill it again. The gearbox filler is hidden up the side of the gearbox and lack of space is a problem&lt;br /&gt;
&lt;br /&gt;
On the Transfer Box disconnect the 4WD switch wire at coupler and unclamp harness. Then disconnect the speed sensor coupler.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 7. Transfer Box Fillers and Connectors.png|thumb|left|250px|Figure 7. Transfer Box Fillers and Connectors]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Now remove the front section of the exhaust pipe. This is held in place by pairs of springs with bolts inside. Due to the heat and stress the front bolts were really, really difficult to move. So much so I think there is real possibility of shearing them on some cars. There is a pair at the front and a pair at the back.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 8. Exhaust Bolts.png|thumb|left|250px|Figure 8. Exhaust Bolts]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Do not lift the exhaust of the rubber hangers yet. There is a Lambda sensor connected to the top of the catalytic converter.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 9. Lambda Sensor on Converter.png|thumb|left|250px|Figure 9. Lambda Sensor on Converter]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
This needs to be disconnected. The Suzuki manual shows the sensor being unscrewed from the top of the converter. However, the sensor has been subject to red hot heat, water and mud, therefore mine was firmly rusted in. Instead I followed the wiring back up to behind the engine. Just behind the head on the passenger side is a set of connectors, unbolt the connector mounting bracket and prise the Lambda connector apart (this is very stiff as well!).&lt;br /&gt;
&lt;br /&gt;
[[File:Lambda Sensor Connector Behind Here.png|thumb|left|250px|Lambda Sensor Connector Behind Here]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
With the Lambda sensor disconnected you can pull the front exhaust section off the rubber mounts.&lt;br /&gt;
&lt;br /&gt;
Now remove the propshafts. On each shaft paint some marks so they can be rebolted to the flanges in the correct position when you are re-building it. Paint all the flanges and also mark the sliding joint in the front propshaft. Remove the FRONT propshaft FIRST, followed by the Gearbox/Transfer box shaft SECOND. Where possible do the REAR propshaft LAST. Why! – because all the propshaft bolts are quite tight and therefore you need to hold the propshafts in place whilst you try to undo the bolts. As the front hubs are vacuum operated there is no easy way to lock the props if you have disconnected the rear first. With the rear prop still on the rear wheels keep the system locked. I found out this trick the hard way.&lt;br /&gt;
&lt;br /&gt;
[[File:Mark the Propshaft.png|thumb|left|250px|Mark the Propshaft]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Now undo the 3 large mounting nuts on the transfer box mount and the 4 bolts on the mounting flange. Now the transfer box should lift down.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 10. Transfer mounts.png|thumb|left|250px|Figure 10. Transfer mounts]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 11. Transfer Mounts.png|thumb|left|250px|Figure 11. Transfer Mounts]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Now for the complex bit. The Jimny has a remote gearbox mechanism bolted onto the rear of the gearbox and this needs to be removed. It’s probably easier to see the part after it has been removed as it is clearer what you are trying to achieve. Note this is the top view, you will normally be underneath!&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 12. Gearbox Remote Mechanism.png|thumb|left|250px|Figure 12. Gearbox Remote Mechanism]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Remove gear shift control joint bolt and extension rod bolt.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 13. Remote Mechanism in place.png|thumb|left|250px|Figure 13. Remote Mechanism in place]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;/div&gt;</summary>
		<author><name>Leftcase</name></author>
	</entry>
	<entry>
		<id>https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_15_-_remote_mechanism_in_place.png&amp;diff=612</id>
		<title>File:Clutch replacement guide - figure 15 - remote mechanism in place.png</title>
		<link rel="alternate" type="text/html" href="https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_15_-_remote_mechanism_in_place.png&amp;diff=612"/>
		<updated>2016-06-03T19:29:55Z</updated>

		<summary type="html">&lt;p&gt;Leftcase: &lt;/p&gt;
&lt;hr /&gt;
&lt;div&gt;&lt;/div&gt;</summary>
		<author><name>Leftcase</name></author>
	</entry>
	<entry>
		<id>https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_14_-_gear_box_remote_mechanism.png&amp;diff=611</id>
		<title>File:Clutch replacement guide - figure 14 - gear box remote mechanism.png</title>
		<link rel="alternate" type="text/html" href="https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_14_-_gear_box_remote_mechanism.png&amp;diff=611"/>
		<updated>2016-06-03T19:28:23Z</updated>

		<summary type="html">&lt;p&gt;Leftcase: &lt;/p&gt;
&lt;hr /&gt;
&lt;div&gt;&lt;/div&gt;</summary>
		<author><name>Leftcase</name></author>
	</entry>
	<entry>
		<id>https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_13_-_transfer_box_mounts.png&amp;diff=610</id>
		<title>File:Clutch replacement guide - figure 13 - transfer box mounts.png</title>
		<link rel="alternate" type="text/html" href="https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_13_-_transfer_box_mounts.png&amp;diff=610"/>
		<updated>2016-06-03T19:27:03Z</updated>

		<summary type="html">&lt;p&gt;Leftcase: &lt;/p&gt;
&lt;hr /&gt;
&lt;div&gt;&lt;/div&gt;</summary>
		<author><name>Leftcase</name></author>
	</entry>
	<entry>
		<id>https://www.bigjimny.com/mediawiki/index.php?title=Clutch_replacement&amp;diff=609</id>
		<title>Clutch replacement</title>
		<link rel="alternate" type="text/html" href="https://www.bigjimny.com/mediawiki/index.php?title=Clutch_replacement&amp;diff=609"/>
		<updated>2016-06-03T19:26:33Z</updated>

		<summary type="html">&lt;p&gt;Leftcase: &lt;/p&gt;
&lt;hr /&gt;
&lt;div&gt;&lt;br /&gt;
== A guide to changing the clutch. ==&lt;br /&gt;
&lt;br /&gt;
It is inevitable that at some point you will have to face changing the clutch. It dips in and out of the mud on a regular basis as the bell-housing is not sealed. Eventually the clutch thrust bearing will start rattling and the action will become stiff and heavy.&lt;br /&gt;
Changing the clutch on a Jimny seems to be not for the faint hearted. It’s a very physical task and it is not pleasant struggling with the gearbox under the car, it is a very tight fit in the transmission tunnel.&lt;br /&gt;
&lt;br /&gt;
No special tools are required, but a good toolkit is needed. You will need extension bars for a socket set as some of the bolts are well hidden and difficult to access.&lt;br /&gt;
A breaker bar is also needed as some bolts are very tight.&lt;br /&gt;
&lt;br /&gt;
If this hasn’t put you off then its time to start work. It goes without saying that you should jet-wash the underside of the car if possible to remove as much of the muck before it drops on you!&lt;br /&gt;
There are two ways of changing the clutch, one is to take the engine and gearbox out and the other is to drop the gearbox off. The Suzuki factory manual suggests the gearbox dropping method so that is the way I have gone.&lt;br /&gt;
&lt;br /&gt;
The factory manual suggests it is not necessary to remove the transfer box, but I have removed it as you will need all the space you can get, I thoroughly recommend that you also remove the transfer box.&lt;br /&gt;
&lt;br /&gt;
If you have the luxury of a bit of time then spray the visible bolts with WD40 a day or so before. In particular you should try and spray the bolts holding the exhaust front section and the bolts around the gearbox housing as these are difficult.&lt;br /&gt;
&lt;br /&gt;
Starting inside the car it is necessary to remove both the gear lever and the transfer box lever.&lt;br /&gt;
&lt;br /&gt;
To remove the gearbox lever you have to remove the centre console. This is held on by four screws on the side at the front and back.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 1. Removing the Centre Console.png|thumb|left|250px|Figure 1. Removing the Centre Console]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
The console then lifts out. Mine was more of a problem as I have a switch panel fitted so I then needed to remove the gearlever before the console would come completely away, but this has to be done at some point anyway. Pull the gaiter away to reveal the three bolt heads around the base of the gearlever, undo the bolts and carefully lift out the gearstick, note that there is a small spring and a cup that should not be lost!&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 2. Removing the Gearlever.png|thumb|left|250px|Figure 2. Removing the Gearlever]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
With the console removed you will then see a frame that holds in a second gaiter. Simply undo the bolts and lift the frame clear.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 3. Removing the lower Gaiter.png|thumb|left|250px|Figure 3. Removing the lower Gaiter]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
If you are removing the Transfer Box then you need to remove the gaiter etc. around the Transfer Box Level. First locate the small screw at the rear of the transfer knob and remove it.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 4. Removing the Transfer Lever Knob.png|thumb|left|250px|Figure 4. Removing the Transfer Lever Knob]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Unscrew the frame around the gaiter and pull the frame and gaiter clear.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 5. Removing the Transfer Level Gaiter.png|thumb|left|250px|Figure 5. Removing the Transfer Level Gaiter]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Move outside the car and disconnect the negative cable at battery.&lt;br /&gt;
Now drain the oil from the gearbox and transfer box, if you are not doing any work on the transfer box then it is not strictly necessary to drain the oil providing you keep it upright to stop the oil coming out of the lever hole.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 6. Gearbox Drain Plugs.png|thumb|left|250px|Figure 6. Gearbox Drain Plugs]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
On my Jimny the drain plugs are square and therefore the square end of a 3/8 socket driver fits. Always undo the filler plug first because if the filler is stuck you do not want to drain the oil and not be able to fill it again. The gearbox filler is hidden up the side of the gearbox and lack of space is a problem&lt;br /&gt;
&lt;br /&gt;
On the Transfer Box disconnect the 4WD switch wire at coupler and unclamp harness. Then disconnect the speed sensor coupler.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 7. Transfer Box Fillers and Connectors.png|thumb|left|250px|Figure 7. Transfer Box Fillers and Connectors]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Now remove the front section of the exhaust pipe. This is held in place by pairs of springs with bolts inside. Due to the heat and stress the front bolts were really, really difficult to move. So much so I think there is real possibility of shearing them on some cars. There is a pair at the front and a pair at the back.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 8. Exhaust Bolts.png|thumb|left|250px|Figure 8. Exhaust Bolts]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Do not lift the exhaust of the rubber hangers yet. There is a Lambda sensor connected to the top of the catalytic converter.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 9. Lambda Sensor on Converter.png|thumb|left|250px|Figure 9. Lambda Sensor on Converter]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
This needs to be disconnected. The Suzuki manual shows the sensor being unscrewed from the top of the converter. However, the sensor has been subject to red hot heat, water and mud, therefore mine was firmly rusted in. Instead I followed the wiring back up to behind the engine. Just behind the head on the passenger side is a set of connectors, unbolt the connector mounting bracket and prise the Lambda connector apart (this is very stiff as well!).&lt;br /&gt;
&lt;br /&gt;
[[File:Lambda Sensor Connector Behind Here.png|thumb|left|250px|Lambda Sensor Connector Behind Here]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
With the Lambda sensor disconnected you can pull the front exhaust section off the rubber mounts.&lt;br /&gt;
&lt;br /&gt;
Now remove the propshafts. On each shaft paint some marks so they can be rebolted to the flanges in the correct position when you are re-building it. Paint all the flanges and also mark the sliding joint in the front propshaft. Remove the FRONT propshaft FIRST, followed by the Gearbox/Transfer box shaft SECOND. Where possible do the REAR propshaft LAST. Why! – because all the propshaft bolts are quite tight and therefore you need to hold the propshafts in place whilst you try to undo the bolts. As the front hubs are vacuum operated there is no easy way to lock the props if you have disconnected the rear first. With the rear prop still on the rear wheels keep the system locked. I found out this trick the hard way.&lt;br /&gt;
&lt;br /&gt;
[[File:Mark the Propshaft.png|thumb|left|250px|Mark the Propshaft]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Now undo the 3 large mounting nuts on the transfer box mount and the 4 bolts on the mounting flange. Now the transfer box should lift down.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 10. Transfer mounts.png|thumb|left|250px|Figure 10. Transfer mounts]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 11. Transfer Mounts.png|thumb|left|250px|Figure 11. Transfer Mounts]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;/div&gt;</summary>
		<author><name>Leftcase</name></author>
	</entry>
	<entry>
		<id>https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_12_-_transfer_box_mounts.png&amp;diff=608</id>
		<title>File:Clutch replacement guide - figure 12 - transfer box mounts.png</title>
		<link rel="alternate" type="text/html" href="https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_12_-_transfer_box_mounts.png&amp;diff=608"/>
		<updated>2016-06-03T19:25:18Z</updated>

		<summary type="html">&lt;p&gt;Leftcase: &lt;/p&gt;
&lt;hr /&gt;
&lt;div&gt;&lt;/div&gt;</summary>
		<author><name>Leftcase</name></author>
	</entry>
	<entry>
		<id>https://www.bigjimny.com/mediawiki/index.php?title=Clutch_replacement&amp;diff=607</id>
		<title>Clutch replacement</title>
		<link rel="alternate" type="text/html" href="https://www.bigjimny.com/mediawiki/index.php?title=Clutch_replacement&amp;diff=607"/>
		<updated>2016-06-03T19:24:57Z</updated>

		<summary type="html">&lt;p&gt;Leftcase: &lt;/p&gt;
&lt;hr /&gt;
&lt;div&gt;&lt;br /&gt;
== A guide to changing the clutch. ==&lt;br /&gt;
&lt;br /&gt;
It is inevitable that at some point you will have to face changing the clutch. It dips in and out of the mud on a regular basis as the bell-housing is not sealed. Eventually the clutch thrust bearing will start rattling and the action will become stiff and heavy.&lt;br /&gt;
Changing the clutch on a Jimny seems to be not for the faint hearted. It’s a very physical task and it is not pleasant struggling with the gearbox under the car, it is a very tight fit in the transmission tunnel.&lt;br /&gt;
&lt;br /&gt;
No special tools are required, but a good toolkit is needed. You will need extension bars for a socket set as some of the bolts are well hidden and difficult to access.&lt;br /&gt;
A breaker bar is also needed as some bolts are very tight.&lt;br /&gt;
&lt;br /&gt;
If this hasn’t put you off then its time to start work. It goes without saying that you should jet-wash the underside of the car if possible to remove as much of the muck before it drops on you!&lt;br /&gt;
There are two ways of changing the clutch, one is to take the engine and gearbox out and the other is to drop the gearbox off. The Suzuki factory manual suggests the gearbox dropping method so that is the way I have gone.&lt;br /&gt;
&lt;br /&gt;
The factory manual suggests it is not necessary to remove the transfer box, but I have removed it as you will need all the space you can get, I thoroughly recommend that you also remove the transfer box.&lt;br /&gt;
&lt;br /&gt;
If you have the luxury of a bit of time then spray the visible bolts with WD40 a day or so before. In particular you should try and spray the bolts holding the exhaust front section and the bolts around the gearbox housing as these are difficult.&lt;br /&gt;
&lt;br /&gt;
Starting inside the car it is necessary to remove both the gear lever and the transfer box lever.&lt;br /&gt;
&lt;br /&gt;
To remove the gearbox lever you have to remove the centre console. This is held on by four screws on the side at the front and back.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 1. Removing the Centre Console.png|thumb|left|250px|Figure 1. Removing the Centre Console]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
The console then lifts out. Mine was more of a problem as I have a switch panel fitted so I then needed to remove the gearlever before the console would come completely away, but this has to be done at some point anyway. Pull the gaiter away to reveal the three bolt heads around the base of the gearlever, undo the bolts and carefully lift out the gearstick, note that there is a small spring and a cup that should not be lost!&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 2. Removing the Gearlever.png|thumb|left|250px|Figure 2. Removing the Gearlever]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
With the console removed you will then see a frame that holds in a second gaiter. Simply undo the bolts and lift the frame clear.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 3. Removing the lower Gaiter.png|thumb|left|250px|Figure 3. Removing the lower Gaiter]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
If you are removing the Transfer Box then you need to remove the gaiter etc. around the Transfer Box Level. First locate the small screw at the rear of the transfer knob and remove it.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 4. Removing the Transfer Lever Knob.png|thumb|left|250px|Figure 4. Removing the Transfer Lever Knob]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Unscrew the frame around the gaiter and pull the frame and gaiter clear.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 5. Removing the Transfer Level Gaiter.png|thumb|left|250px|Figure 5. Removing the Transfer Level Gaiter]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Move outside the car and disconnect the negative cable at battery.&lt;br /&gt;
Now drain the oil from the gearbox and transfer box, if you are not doing any work on the transfer box then it is not strictly necessary to drain the oil providing you keep it upright to stop the oil coming out of the lever hole.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 6. Gearbox Drain Plugs.png|thumb|left|250px|Figure 6. Gearbox Drain Plugs]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
On my Jimny the drain plugs are square and therefore the square end of a 3/8 socket driver fits. Always undo the filler plug first because if the filler is stuck you do not want to drain the oil and not be able to fill it again. The gearbox filler is hidden up the side of the gearbox and lack of space is a problem&lt;br /&gt;
&lt;br /&gt;
On the Transfer Box disconnect the 4WD switch wire at coupler and unclamp harness. Then disconnect the speed sensor coupler.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 7. Transfer Box Fillers and Connectors.png|thumb|left|250px|Figure 7. Transfer Box Fillers and Connectors]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Now remove the front section of the exhaust pipe. This is held in place by pairs of springs with bolts inside. Due to the heat and stress the front bolts were really, really difficult to move. So much so I think there is real possibility of shearing them on some cars. There is a pair at the front and a pair at the back.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 8. Exhaust Bolts.png|thumb|left|250px|Figure 8. Exhaust Bolts]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Do not lift the exhaust of the rubber hangers yet. There is a Lambda sensor connected to the top of the catalytic converter.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 9. Lambda Sensor on Converter.png|thumb|left|250px|Figure 9. Lambda Sensor on Converter]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
This needs to be disconnected. The Suzuki manual shows the sensor being unscrewed from the top of the converter. However, the sensor has been subject to red hot heat, water and mud, therefore mine was firmly rusted in. Instead I followed the wiring back up to behind the engine. Just behind the head on the passenger side is a set of connectors, unbolt the connector mounting bracket and prise the Lambda connector apart (this is very stiff as well!).&lt;br /&gt;
&lt;br /&gt;
[[File:Lambda Sensor Connector Behind Here.png|thumb|left|250px|Lambda Sensor Connector Behind Here]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
With the Lambda sensor disconnected you can pull the front exhaust section off the rubber mounts.&lt;br /&gt;
&lt;br /&gt;
Now remove the propshafts. On each shaft paint some marks so they can be rebolted to the flanges in the correct position when you are re-building it. Paint all the flanges and also mark the sliding joint in the front propshaft. Remove the FRONT propshaft FIRST, followed by the Gearbox/Transfer box shaft SECOND. Where possible do the REAR propshaft LAST. Why! – because all the propshaft bolts are quite tight and therefore you need to hold the propshafts in place whilst you try to undo the bolts. As the front hubs are vacuum operated there is no easy way to lock the props if you have disconnected the rear first. With the rear prop still on the rear wheels keep the system locked. I found out this trick the hard way.&lt;br /&gt;
&lt;br /&gt;
[[File:Mark the Propshaft.png|thumb|left|250px|Mark the Propshaft]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Now undo the 3 large mounting nuts on the transfer box mount and the 4 bolts on the mounting flange. Now the transfer box should lift down.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 10. Transfer mounts.png|thumb|left|250px|Figure 10. Transfer mounts]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;/div&gt;</summary>
		<author><name>Leftcase</name></author>
	</entry>
	<entry>
		<id>https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_11_-_mark_the_propeller_shaft.png&amp;diff=606</id>
		<title>File:Clutch replacement guide - figure 11 - mark the propeller shaft.png</title>
		<link rel="alternate" type="text/html" href="https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_11_-_mark_the_propeller_shaft.png&amp;diff=606"/>
		<updated>2016-06-03T19:22:41Z</updated>

		<summary type="html">&lt;p&gt;Leftcase: &lt;/p&gt;
&lt;hr /&gt;
&lt;div&gt;&lt;/div&gt;</summary>
		<author><name>Leftcase</name></author>
	</entry>
	<entry>
		<id>https://www.bigjimny.com/mediawiki/index.php?title=Clutch_replacement&amp;diff=605</id>
		<title>Clutch replacement</title>
		<link rel="alternate" type="text/html" href="https://www.bigjimny.com/mediawiki/index.php?title=Clutch_replacement&amp;diff=605"/>
		<updated>2016-06-03T19:21:28Z</updated>

		<summary type="html">&lt;p&gt;Leftcase: /* A guide to changing the clutch. */&lt;/p&gt;
&lt;hr /&gt;
&lt;div&gt;&lt;br /&gt;
== A guide to changing the clutch. ==&lt;br /&gt;
&lt;br /&gt;
It is inevitable that at some point you will have to face changing the clutch. It dips in and out of the mud on a regular basis as the bell-housing is not sealed. Eventually the clutch thrust bearing will start rattling and the action will become stiff and heavy.&lt;br /&gt;
Changing the clutch on a Jimny seems to be not for the faint hearted. It’s a very physical task and it is not pleasant struggling with the gearbox under the car, it is a very tight fit in the transmission tunnel.&lt;br /&gt;
&lt;br /&gt;
No special tools are required, but a good toolkit is needed. You will need extension bars for a socket set as some of the bolts are well hidden and difficult to access.&lt;br /&gt;
A breaker bar is also needed as some bolts are very tight.&lt;br /&gt;
&lt;br /&gt;
If this hasn’t put you off then its time to start work. It goes without saying that you should jet-wash the underside of the car if possible to remove as much of the muck before it drops on you!&lt;br /&gt;
There are two ways of changing the clutch, one is to take the engine and gearbox out and the other is to drop the gearbox off. The Suzuki factory manual suggests the gearbox dropping method so that is the way I have gone.&lt;br /&gt;
&lt;br /&gt;
The factory manual suggests it is not necessary to remove the transfer box, but I have removed it as you will need all the space you can get, I thoroughly recommend that you also remove the transfer box.&lt;br /&gt;
&lt;br /&gt;
If you have the luxury of a bit of time then spray the visible bolts with WD40 a day or so before. In particular you should try and spray the bolts holding the exhaust front section and the bolts around the gearbox housing as these are difficult.&lt;br /&gt;
&lt;br /&gt;
Starting inside the car it is necessary to remove both the gear lever and the transfer box lever.&lt;br /&gt;
&lt;br /&gt;
To remove the gearbox lever you have to remove the centre console. This is held on by four screws on the side at the front and back.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 1. Removing the Centre Console.png|thumb|left|250px|Figure 1. Removing the Centre Console]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
The console then lifts out. Mine was more of a problem as I have a switch panel fitted so I then needed to remove the gearlever before the console would come completely away, but this has to be done at some point anyway. Pull the gaiter away to reveal the three bolt heads around the base of the gearlever, undo the bolts and carefully lift out the gearstick, note that there is a small spring and a cup that should not be lost!&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 2. Removing the Gearlever.png|thumb|left|250px|Figure 2. Removing the Gearlever]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
With the console removed you will then see a frame that holds in a second gaiter. Simply undo the bolts and lift the frame clear.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 3. Removing the lower Gaiter.png|thumb|left|250px|Figure 3. Removing the lower Gaiter]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
If you are removing the Transfer Box then you need to remove the gaiter etc. around the Transfer Box Level. First locate the small screw at the rear of the transfer knob and remove it.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 4. Removing the Transfer Lever Knob.png|thumb|left|250px|Figure 4. Removing the Transfer Lever Knob]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Unscrew the frame around the gaiter and pull the frame and gaiter clear.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 5. Removing the Transfer Level Gaiter.png|thumb|left|250px|Figure 5. Removing the Transfer Level Gaiter]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Move outside the car and disconnect the negative cable at battery.&lt;br /&gt;
Now drain the oil from the gearbox and transfer box, if you are not doing any work on the transfer box then it is not strictly necessary to drain the oil providing you keep it upright to stop the oil coming out of the lever hole.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 6. Gearbox Drain Plugs.png|thumb|left|250px|Figure 6. Gearbox Drain Plugs]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
On my Jimny the drain plugs are square and therefore the square end of a 3/8 socket driver fits. Always undo the filler plug first because if the filler is stuck you do not want to drain the oil and not be able to fill it again. The gearbox filler is hidden up the side of the gearbox and lack of space is a problem&lt;br /&gt;
&lt;br /&gt;
On the Transfer Box disconnect the 4WD switch wire at coupler and unclamp harness. Then disconnect the speed sensor coupler.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 7. Transfer Box Fillers and Connectors.png|thumb|left|250px|Figure 7. Transfer Box Fillers and Connectors]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Now remove the front section of the exhaust pipe. This is held in place by pairs of springs with bolts inside. Due to the heat and stress the front bolts were really, really difficult to move. So much so I think there is real possibility of shearing them on some cars. There is a pair at the front and a pair at the back.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 8. Exhaust Bolts.png|thumb|left|250px|Figure 8. Exhaust Bolts]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Do not lift the exhaust of the rubber hangers yet. There is a Lambda sensor connected to the top of the catalytic converter.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 9. Lambda Sensor on Converter.png|thumb|left|250px|Figure 9. Lambda Sensor on Converter]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
This needs to be disconnected. The Suzuki manual shows the sensor being unscrewed from the top of the converter. However, the sensor has been subject to red hot heat, water and mud, therefore mine was firmly rusted in. Instead I followed the wiring back up to behind the engine. Just behind the head on the passenger side is a set of connectors, unbolt the connector mounting bracket and prise the Lambda connector apart (this is very stiff as well!).&lt;br /&gt;
&lt;br /&gt;
[[File:Lambda Sensor Connector Behind Here.png|thumb|left|250px|Lambda Sensor Connector Behind Here]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
&lt;br /&gt;
With the Lambda sensor disconnected you can pull the front exhaust section off the rubber mounts.&lt;br /&gt;
&lt;br /&gt;
Now remove the propshafts. On each shaft paint some marks so they can be rebolted to the flanges in the correct position when you are re-building it. Paint all the flanges and also mark the sliding joint in the front propshaft. Remove the FRONT propshaft FIRST, followed by the Gearbox/Transfer box shaft SECOND. Where possible do the REAR propshaft LAST. Why! – because all the propshaft bolts are quite tight and therefore you need to hold the propshafts in place whilst you try to undo the bolts. As the front hubs are vacuum operated there is no easy way to lock the props if you have disconnected the rear first. With the rear prop still on the rear wheels keep the system locked. I found out this trick the hard way.&lt;/div&gt;</summary>
		<author><name>Leftcase</name></author>
	</entry>
	<entry>
		<id>https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_10_-_lambda_sensor_connector_behind_here.png&amp;diff=604</id>
		<title>File:Clutch replacement guide - figure 10 - lambda sensor connector behind here.png</title>
		<link rel="alternate" type="text/html" href="https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_10_-_lambda_sensor_connector_behind_here.png&amp;diff=604"/>
		<updated>2016-06-03T19:20:03Z</updated>

		<summary type="html">&lt;p&gt;Leftcase: &lt;/p&gt;
&lt;hr /&gt;
&lt;div&gt;&lt;/div&gt;</summary>
		<author><name>Leftcase</name></author>
	</entry>
	<entry>
		<id>https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_09_-_lambda_sensor_on_converter.png&amp;diff=603</id>
		<title>File:Clutch replacement guide - figure 09 - lambda sensor on converter.png</title>
		<link rel="alternate" type="text/html" href="https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_09_-_lambda_sensor_on_converter.png&amp;diff=603"/>
		<updated>2016-06-03T19:18:21Z</updated>

		<summary type="html">&lt;p&gt;Leftcase: &lt;/p&gt;
&lt;hr /&gt;
&lt;div&gt;&lt;/div&gt;</summary>
		<author><name>Leftcase</name></author>
	</entry>
	<entry>
		<id>https://www.bigjimny.com/mediawiki/index.php?title=Clutch_replacement&amp;diff=602</id>
		<title>Clutch replacement</title>
		<link rel="alternate" type="text/html" href="https://www.bigjimny.com/mediawiki/index.php?title=Clutch_replacement&amp;diff=602"/>
		<updated>2016-06-03T19:17:58Z</updated>

		<summary type="html">&lt;p&gt;Leftcase: /* A guide to changing the clutch. */&lt;/p&gt;
&lt;hr /&gt;
&lt;div&gt;&lt;br /&gt;
== A guide to changing the clutch. ==&lt;br /&gt;
&lt;br /&gt;
It is inevitable that at some point you will have to face changing the clutch. It dips in and out of the mud on a regular basis as the bell-housing is not sealed. Eventually the clutch thrust bearing will start rattling and the action will become stiff and heavy.&lt;br /&gt;
Changing the clutch on a Jimny seems to be not for the faint hearted. It’s a very physical task and it is not pleasant struggling with the gearbox under the car, it is a very tight fit in the transmission tunnel.&lt;br /&gt;
&lt;br /&gt;
No special tools are required, but a good toolkit is needed. You will need extension bars for a socket set as some of the bolts are well hidden and difficult to access.&lt;br /&gt;
A breaker bar is also needed as some bolts are very tight.&lt;br /&gt;
&lt;br /&gt;
If this hasn’t put you off then its time to start work. It goes without saying that you should jet-wash the underside of the car if possible to remove as much of the muck before it drops on you!&lt;br /&gt;
There are two ways of changing the clutch, one is to take the engine and gearbox out and the other is to drop the gearbox off. The Suzuki factory manual suggests the gearbox dropping method so that is the way I have gone.&lt;br /&gt;
&lt;br /&gt;
The factory manual suggests it is not necessary to remove the transfer box, but I have removed it as you will need all the space you can get, I thoroughly recommend that you also remove the transfer box.&lt;br /&gt;
&lt;br /&gt;
If you have the luxury of a bit of time then spray the visible bolts with WD40 a day or so before. In particular you should try and spray the bolts holding the exhaust front section and the bolts around the gearbox housing as these are difficult.&lt;br /&gt;
&lt;br /&gt;
Starting inside the car it is necessary to remove both the gear lever and the transfer box lever.&lt;br /&gt;
&lt;br /&gt;
To remove the gearbox lever you have to remove the centre console. This is held on by four screws on the side at the front and back.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 1. Removing the Centre Console.png|thumb|left|250px|Figure 1. Removing the Centre Console]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
The console then lifts out. Mine was more of a problem as I have a switch panel fitted so I then needed to remove the gearlever before the console would come completely away, but this has to be done at some point anyway. Pull the gaiter away to reveal the three bolt heads around the base of the gearlever, undo the bolts and carefully lift out the gearstick, note that there is a small spring and a cup that should not be lost!&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 2. Removing the Gearlever.png|thumb|left|250px|Figure 2. Removing the Gearlever]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
With the console removed you will then see a frame that holds in a second gaiter. Simply undo the bolts and lift the frame clear.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 3. Removing the lower Gaiter.png|thumb|left|250px|Figure 3. Removing the lower Gaiter]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
If you are removing the Transfer Box then you need to remove the gaiter etc. around the Transfer Box Level. First locate the small screw at the rear of the transfer knob and remove it.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 4. Removing the Transfer Lever Knob.png|thumb|left|250px|Figure 4. Removing the Transfer Lever Knob]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Unscrew the frame around the gaiter and pull the frame and gaiter clear.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 5. Removing the Transfer Level Gaiter.png|thumb|left|250px|Figure 5. Removing the Transfer Level Gaiter]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Move outside the car and disconnect the negative cable at battery.&lt;br /&gt;
Now drain the oil from the gearbox and transfer box, if you are not doing any work on the transfer box then it is not strictly necessary to drain the oil providing you keep it upright to stop the oil coming out of the lever hole.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 6. Gearbox Drain Plugs.png|thumb|left|250px|Figure 6. Gearbox Drain Plugs]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
On my Jimny the drain plugs are square and therefore the square end of a 3/8 socket driver fits. Always undo the filler plug first because if the filler is stuck you do not want to drain the oil and not be able to fill it again. The gearbox filler is hidden up the side of the gearbox and lack of space is a problem&lt;br /&gt;
&lt;br /&gt;
On the Transfer Box disconnect the 4WD switch wire at coupler and unclamp harness. Then disconnect the speed sensor coupler.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 7. Transfer Box Fillers and Connectors.png|thumb|left|250px|Figure 7. Transfer Box Fillers and Connectors]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Now remove the front section of the exhaust pipe. This is held in place by pairs of springs with bolts inside. Due to the heat and stress the front bolts were really, really difficult to move. So much so I think there is real possibility of shearing them on some cars. There is a pair at the front and a pair at the back.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 8. Exhaust Bolts.png|thumb|left|250px|Figure 8. Exhaust Bolts]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Do not lift the exhaust of the rubber hangers yet. There is a Lambda sensor connected to the top of the catalytic converter.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 9. Lambda Sensor on Converter.png|thumb|left|250px|Figure 9. Lambda Sensor on Converter]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
This needs to be disconnected. The Suzuki manual shows the sensor being unscrewed from the top of the converter. However, the sensor has been subject to red hot heat, water and mud, therefore mine was firmly rusted in. Instead I followed the wiring back up to behind the engine. Just behind the head on the passenger side is a set of connectors, unbolt the connector mounting bracket and prise the Lambda connector apart (this is very stiff as well!).&lt;/div&gt;</summary>
		<author><name>Leftcase</name></author>
	</entry>
	<entry>
		<id>https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_08_-_exhaust_bolts.png&amp;diff=601</id>
		<title>File:Clutch replacement guide - figure 08 - exhaust bolts.png</title>
		<link rel="alternate" type="text/html" href="https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_08_-_exhaust_bolts.png&amp;diff=601"/>
		<updated>2016-06-03T19:15:23Z</updated>

		<summary type="html">&lt;p&gt;Leftcase: &lt;/p&gt;
&lt;hr /&gt;
&lt;div&gt;&lt;/div&gt;</summary>
		<author><name>Leftcase</name></author>
	</entry>
	<entry>
		<id>https://www.bigjimny.com/mediawiki/index.php?title=Clutch_replacement&amp;diff=600</id>
		<title>Clutch replacement</title>
		<link rel="alternate" type="text/html" href="https://www.bigjimny.com/mediawiki/index.php?title=Clutch_replacement&amp;diff=600"/>
		<updated>2016-06-03T19:13:37Z</updated>

		<summary type="html">&lt;p&gt;Leftcase: &lt;/p&gt;
&lt;hr /&gt;
&lt;div&gt;&lt;br /&gt;
== A guide to changing the clutch. ==&lt;br /&gt;
&lt;br /&gt;
It is inevitable that at some point you will have to face changing the clutch. It dips in and out of the mud on a regular basis as the bell-housing is not sealed. Eventually the clutch thrust bearing will start rattling and the action will become stiff and heavy.&lt;br /&gt;
Changing the clutch on a Jimny seems to be not for the faint hearted. It’s a very physical task and it is not pleasant struggling with the gearbox under the car, it is a very tight fit in the transmission tunnel.&lt;br /&gt;
&lt;br /&gt;
No special tools are required, but a good toolkit is needed. You will need extension bars for a socket set as some of the bolts are well hidden and difficult to access.&lt;br /&gt;
A breaker bar is also needed as some bolts are very tight.&lt;br /&gt;
&lt;br /&gt;
If this hasn’t put you off then its time to start work. It goes without saying that you should jet-wash the underside of the car if possible to remove as much of the muck before it drops on you!&lt;br /&gt;
There are two ways of changing the clutch, one is to take the engine and gearbox out and the other is to drop the gearbox off. The Suzuki factory manual suggests the gearbox dropping method so that is the way I have gone.&lt;br /&gt;
&lt;br /&gt;
The factory manual suggests it is not necessary to remove the transfer box, but I have removed it as you will need all the space you can get, I thoroughly recommend that you also remove the transfer box.&lt;br /&gt;
&lt;br /&gt;
If you have the luxury of a bit of time then spray the visible bolts with WD40 a day or so before. In particular you should try and spray the bolts holding the exhaust front section and the bolts around the gearbox housing as these are difficult.&lt;br /&gt;
&lt;br /&gt;
Starting inside the car it is necessary to remove both the gear lever and the transfer box lever.&lt;br /&gt;
&lt;br /&gt;
To remove the gearbox lever you have to remove the centre console. This is held on by four screws on the side at the front and back.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 1. Removing the Centre Console.png|thumb|left|250px|Figure 1. Removing the Centre Console]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
The console then lifts out. Mine was more of a problem as I have a switch panel fitted so I then needed to remove the gearlever before the console would come completely away, but this has to be done at some point anyway. Pull the gaiter away to reveal the three bolt heads around the base of the gearlever, undo the bolts and carefully lift out the gearstick, note that there is a small spring and a cup that should not be lost!&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 2. Removing the Gearlever.png|thumb|left|250px|Figure 2. Removing the Gearlever]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
With the console removed you will then see a frame that holds in a second gaiter. Simply undo the bolts and lift the frame clear.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 3. Removing the lower Gaiter.png|thumb|left|250px|Figure 3. Removing the lower Gaiter]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
If you are removing the Transfer Box then you need to remove the gaiter etc. around the Transfer Box Level. First locate the small screw at the rear of the transfer knob and remove it.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 4. Removing the Transfer Lever Knob.png|thumb|left|250px|Figure 4. Removing the Transfer Lever Knob]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Unscrew the frame around the gaiter and pull the frame and gaiter clear.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 5. Removing the Transfer Level Gaiter.png|thumb|left|250px|Figure 5. Removing the Transfer Level Gaiter]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Move outside the car and disconnect the negative cable at battery.&lt;br /&gt;
Now drain the oil from the gearbox and transfer box, if you are not doing any work on the transfer box then it is not strictly necessary to drain the oil providing you keep it upright to stop the oil coming out of the lever hole.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 6. Gearbox Drain Plugs.png|thumb|left|250px|Figure 6. Gearbox Drain Plugs]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
On my Jimny the drain plugs are square and therefore the square end of a 3/8 socket driver fits. Always undo the filler plug first because if the filler is stuck you do not want to drain the oil and not be able to fill it again. The gearbox filler is hidden up the side of the gearbox and lack of space is a problem&lt;br /&gt;
&lt;br /&gt;
On the Transfer Box disconnect the 4WD switch wire at coupler and unclamp harness. Then disconnect the speed sensor coupler.&lt;br /&gt;
&lt;br /&gt;
[[Figure 7. Transfer Box Fillers and Connectors.png|thumb|left|250px|Figure 7. Transfer Box Fillers and Connectors]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Now remove the front section of the exhaust pipe. This is held in place by pairs of springs with bolts inside. Due to the heat and stress the front bolts were really, really difficult to move. So much so I think there is real possibility of shearing them on some cars. There is a pair at the front and a pair at the back.&lt;/div&gt;</summary>
		<author><name>Leftcase</name></author>
	</entry>
	<entry>
		<id>https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_07_-_transfer_box_fillers_and_connectors.png&amp;diff=599</id>
		<title>File:Clutch replacement guide - figure 07 - transfer box fillers and connectors.png</title>
		<link rel="alternate" type="text/html" href="https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_07_-_transfer_box_fillers_and_connectors.png&amp;diff=599"/>
		<updated>2016-06-03T19:12:35Z</updated>

		<summary type="html">&lt;p&gt;Leftcase: &lt;/p&gt;
&lt;hr /&gt;
&lt;div&gt;&lt;/div&gt;</summary>
		<author><name>Leftcase</name></author>
	</entry>
	<entry>
		<id>https://www.bigjimny.com/mediawiki/index.php?title=Clutch_replacement&amp;diff=598</id>
		<title>Clutch replacement</title>
		<link rel="alternate" type="text/html" href="https://www.bigjimny.com/mediawiki/index.php?title=Clutch_replacement&amp;diff=598"/>
		<updated>2016-06-03T19:10:34Z</updated>

		<summary type="html">&lt;p&gt;Leftcase: &lt;/p&gt;
&lt;hr /&gt;
&lt;div&gt;&lt;br /&gt;
== A guide to changing the clutch. ==&lt;br /&gt;
&lt;br /&gt;
It is inevitable that at some point you will have to face changing the clutch. It dips in and out of the mud on a regular basis as the bell-housing is not sealed. Eventually the clutch thrust bearing will start rattling and the action will become stiff and heavy.&lt;br /&gt;
Changing the clutch on a Jimny seems to be not for the faint hearted. It’s a very physical task and it is not pleasant struggling with the gearbox under the car, it is a very tight fit in the transmission tunnel.&lt;br /&gt;
&lt;br /&gt;
No special tools are required, but a good toolkit is needed. You will need extension bars for a socket set as some of the bolts are well hidden and difficult to access.&lt;br /&gt;
A breaker bar is also needed as some bolts are very tight.&lt;br /&gt;
&lt;br /&gt;
If this hasn’t put you off then its time to start work. It goes without saying that you should jet-wash the underside of the car if possible to remove as much of the muck before it drops on you!&lt;br /&gt;
There are two ways of changing the clutch, one is to take the engine and gearbox out and the other is to drop the gearbox off. The Suzuki factory manual suggests the gearbox dropping method so that is the way I have gone.&lt;br /&gt;
&lt;br /&gt;
The factory manual suggests it is not necessary to remove the transfer box, but I have removed it as you will need all the space you can get, I thoroughly recommend that you also remove the transfer box.&lt;br /&gt;
&lt;br /&gt;
If you have the luxury of a bit of time then spray the visible bolts with WD40 a day or so before. In particular you should try and spray the bolts holding the exhaust front section and the bolts around the gearbox housing as these are difficult.&lt;br /&gt;
&lt;br /&gt;
Starting inside the car it is necessary to remove both the gear lever and the transfer box lever.&lt;br /&gt;
&lt;br /&gt;
To remove the gearbox lever you have to remove the centre console. This is held on by four screws on the side at the front and back.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 1. Removing the Centre Console.png|thumb|left|250px|Figure 1. Removing the Centre Console]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
The console then lifts out. Mine was more of a problem as I have a switch panel fitted so I then needed to remove the gearlever before the console would come completely away, but this has to be done at some point anyway. Pull the gaiter away to reveal the three bolt heads around the base of the gearlever, undo the bolts and carefully lift out the gearstick, note that there is a small spring and a cup that should not be lost!&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 2. Removing the Gearlever.png|thumb|left|250px|Figure 2. Removing the Gearlever]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
With the console removed you will then see a frame that holds in a second gaiter. Simply undo the bolts and lift the frame clear.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 3. Removing the lower Gaiter.png|thumb|left|250px|Figure 3. Removing the lower Gaiter]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
If you are removing the Transfer Box then you need to remove the gaiter etc. around the Transfer Box Level. First locate the small screw at the rear of the transfer knob and remove it.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 4. Removing the Transfer Lever Knob.png|thumb|left|250px|Figure 4. Removing the Transfer Lever Knob]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Unscrew the frame around the gaiter and pull the frame and gaiter clear.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 5. Removing the Transfer Level Gaiter.png|thumb|left|250px|Figure 5. Removing the Transfer Level Gaiter]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Move outside the car and disconnect the negative cable at battery.&lt;br /&gt;
Now drain the oil from the gearbox and transfer box, if you are not doing any work on the transfer box then it is not strictly necessary to drain the oil providing you keep it upright to stop the oil coming out of the lever hole.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 6. Gearbox Drain Plugs.png|thumb|left|250px|Figure 6. Gearbox Drain Plugs]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;/div&gt;</summary>
		<author><name>Leftcase</name></author>
	</entry>
	<entry>
		<id>https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_06_-_gear_box_drain_plugs.png&amp;diff=597</id>
		<title>File:Clutch replacement guide - figure 06 - gear box drain plugs.png</title>
		<link rel="alternate" type="text/html" href="https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_06_-_gear_box_drain_plugs.png&amp;diff=597"/>
		<updated>2016-06-03T19:09:43Z</updated>

		<summary type="html">&lt;p&gt;Leftcase: &lt;/p&gt;
&lt;hr /&gt;
&lt;div&gt;&lt;/div&gt;</summary>
		<author><name>Leftcase</name></author>
	</entry>
	<entry>
		<id>https://www.bigjimny.com/mediawiki/index.php?title=Clutch_replacement&amp;diff=596</id>
		<title>Clutch replacement</title>
		<link rel="alternate" type="text/html" href="https://www.bigjimny.com/mediawiki/index.php?title=Clutch_replacement&amp;diff=596"/>
		<updated>2016-06-03T19:08:28Z</updated>

		<summary type="html">&lt;p&gt;Leftcase: /* A guide to changing the clutch. */&lt;/p&gt;
&lt;hr /&gt;
&lt;div&gt;&lt;br /&gt;
== A guide to changing the clutch. ==&lt;br /&gt;
&lt;br /&gt;
It is inevitable that at some point you will have to face changing the clutch. It dips in and out of the mud on a regular basis as the bell-housing is not sealed. Eventually the clutch thrust bearing will start rattling and the action will become stiff and heavy.&lt;br /&gt;
Changing the clutch on a Jimny seems to be not for the faint hearted. It’s a very physical task and it is not pleasant struggling with the gearbox under the car, it is a very tight fit in the transmission tunnel.&lt;br /&gt;
&lt;br /&gt;
No special tools are required, but a good toolkit is needed. You will need extension bars for a socket set as some of the bolts are well hidden and difficult to access.&lt;br /&gt;
A breaker bar is also needed as some bolts are very tight.&lt;br /&gt;
&lt;br /&gt;
If this hasn’t put you off then its time to start work. It goes without saying that you should jet-wash the underside of the car if possible to remove as much of the muck before it drops on you!&lt;br /&gt;
There are two ways of changing the clutch, one is to take the engine and gearbox out and the other is to drop the gearbox off. The Suzuki factory manual suggests the gearbox dropping method so that is the way I have gone.&lt;br /&gt;
&lt;br /&gt;
The factory manual suggests it is not necessary to remove the transfer box, but I have removed it as you will need all the space you can get, I thoroughly recommend that you also remove the transfer box.&lt;br /&gt;
&lt;br /&gt;
If you have the luxury of a bit of time then spray the visible bolts with WD40 a day or so before. In particular you should try and spray the bolts holding the exhaust front section and the bolts around the gearbox housing as these are difficult.&lt;br /&gt;
&lt;br /&gt;
Starting inside the car it is necessary to remove both the gear lever and the transfer box lever.&lt;br /&gt;
&lt;br /&gt;
To remove the gearbox lever you have to remove the centre console. This is held on by four screws on the side at the front and back.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 1. Removing the Centre Console.png|thumb|left|250px|Figure 1. Removing the Centre Console]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
The console then lifts out. Mine was more of a problem as I have a switch panel fitted so I then needed to remove the gearlever before the console would come completely away, but this has to be done at some point anyway. Pull the gaiter away to reveal the three bolt heads around the base of the gearlever, undo the bolts and carefully lift out the gearstick, note that there is a small spring and a cup that should not be lost!&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 2. Removing the Gearlever.png|thumb|left|250px|Figure 2. Removing the Gearlever]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
With the console removed you will then see a frame that holds in a second gaiter. Simply undo the bolts and lift the frame clear.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 3. Removing the lower Gaiter.png|thumb|left|250px|Figure 3. Removing the lower Gaiter]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
If you are removing the Transfer Box then you need to remove the gaiter etc. around the Transfer Box Level. First locate the small screw at the rear of the transfer knob and remove it.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 4. Removing the Transfer Lever Knob.png|thumb|left|250px|Figure 4. Removing the Transfer Lever Knob]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Unscrew the frame around the gaiter and pull the frame and gaiter clear.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 5. Removing the Transfer Level Gaiter.png|thumb|left|250px|Figure 5. Removing the Transfer Level Gaiter]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Move outside the car and disconnect the negative cable at battery.&lt;br /&gt;
Now drain the oil from the gearbox and transfer box, if you are not doing any work on the transfer box then it is not strictly necessary to drain the oil providing you keep it upright to stop the oil coming out of the lever hole.&lt;/div&gt;</summary>
		<author><name>Leftcase</name></author>
	</entry>
	<entry>
		<id>https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_05_-_removing_the_transfer_level_gaiter.png&amp;diff=595</id>
		<title>File:Clutch replacement guide - figure 05 - removing the transfer level gaiter.png</title>
		<link rel="alternate" type="text/html" href="https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_05_-_removing_the_transfer_level_gaiter.png&amp;diff=595"/>
		<updated>2016-06-03T19:07:14Z</updated>

		<summary type="html">&lt;p&gt;Leftcase: &lt;/p&gt;
&lt;hr /&gt;
&lt;div&gt;&lt;/div&gt;</summary>
		<author><name>Leftcase</name></author>
	</entry>
	<entry>
		<id>https://www.bigjimny.com/mediawiki/index.php?title=Clutch_replacement&amp;diff=594</id>
		<title>Clutch replacement</title>
		<link rel="alternate" type="text/html" href="https://www.bigjimny.com/mediawiki/index.php?title=Clutch_replacement&amp;diff=594"/>
		<updated>2016-06-03T19:05:22Z</updated>

		<summary type="html">&lt;p&gt;Leftcase: /* A guide to changing the clutch. */&lt;/p&gt;
&lt;hr /&gt;
&lt;div&gt;&lt;br /&gt;
== A guide to changing the clutch. ==&lt;br /&gt;
&lt;br /&gt;
It is inevitable that at some point you will have to face changing the clutch. It dips in and out of the mud on a regular basis as the bell-housing is not sealed. Eventually the clutch thrust bearing will start rattling and the action will become stiff and heavy.&lt;br /&gt;
Changing the clutch on a Jimny seems to be not for the faint hearted. It’s a very physical task and it is not pleasant struggling with the gearbox under the car, it is a very tight fit in the transmission tunnel.&lt;br /&gt;
&lt;br /&gt;
No special tools are required, but a good toolkit is needed. You will need extension bars for a socket set as some of the bolts are well hidden and difficult to access.&lt;br /&gt;
A breaker bar is also needed as some bolts are very tight.&lt;br /&gt;
&lt;br /&gt;
If this hasn’t put you off then its time to start work. It goes without saying that you should jet-wash the underside of the car if possible to remove as much of the muck before it drops on you!&lt;br /&gt;
There are two ways of changing the clutch, one is to take the engine and gearbox out and the other is to drop the gearbox off. The Suzuki factory manual suggests the gearbox dropping method so that is the way I have gone.&lt;br /&gt;
&lt;br /&gt;
The factory manual suggests it is not necessary to remove the transfer box, but I have removed it as you will need all the space you can get, I thoroughly recommend that you also remove the transfer box.&lt;br /&gt;
&lt;br /&gt;
If you have the luxury of a bit of time then spray the visible bolts with WD40 a day or so before. In particular you should try and spray the bolts holding the exhaust front section and the bolts around the gearbox housing as these are difficult.&lt;br /&gt;
&lt;br /&gt;
Starting inside the car it is necessary to remove both the gear lever and the transfer box lever.&lt;br /&gt;
&lt;br /&gt;
To remove the gearbox lever you have to remove the centre console. This is held on by four screws on the side at the front and back.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 1. Removing the Centre Console.png|thumb|left|250px|Figure 1. Removing the Centre Console]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
The console then lifts out. Mine was more of a problem as I have a switch panel fitted so I then needed to remove the gearlever before the console would come completely away, but this has to be done at some point anyway. Pull the gaiter away to reveal the three bolt heads around the base of the gearlever, undo the bolts and carefully lift out the gearstick, note that there is a small spring and a cup that should not be lost!&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 2. Removing the Gearlever.png|thumb|left|250px|Figure 2. Removing the Gearlever]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
With the console removed you will then see a frame that holds in a second gaiter. Simply undo the bolts and lift the frame clear.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 3. Removing the lower Gaiter.png|thumb|left|250px|Figure 3. Removing the lower Gaiter]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
If you are removing the Transfer Box then you need to remove the gaiter etc. around the Transfer Box Level. First locate the small screw at the rear of the transfer knob and remove it.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 4. Removing the Transfer Lever Knob.png|thumb|left|250px|Figure 4. Removing the Transfer Lever Knob]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
Unscrew the frame around the gaiter and pull the frame and gaiter clear.&lt;/div&gt;</summary>
		<author><name>Leftcase</name></author>
	</entry>
	<entry>
		<id>https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_04_-_removing_the_transfer_lever_knob.png&amp;diff=593</id>
		<title>File:Clutch replacement guide - figure 04 - removing the transfer lever knob.png</title>
		<link rel="alternate" type="text/html" href="https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_04_-_removing_the_transfer_lever_knob.png&amp;diff=593"/>
		<updated>2016-06-03T19:04:12Z</updated>

		<summary type="html">&lt;p&gt;Leftcase: &lt;/p&gt;
&lt;hr /&gt;
&lt;div&gt;&lt;/div&gt;</summary>
		<author><name>Leftcase</name></author>
	</entry>
	<entry>
		<id>https://www.bigjimny.com/mediawiki/index.php?title=Clutch_replacement&amp;diff=592</id>
		<title>Clutch replacement</title>
		<link rel="alternate" type="text/html" href="https://www.bigjimny.com/mediawiki/index.php?title=Clutch_replacement&amp;diff=592"/>
		<updated>2016-06-03T19:02:18Z</updated>

		<summary type="html">&lt;p&gt;Leftcase: /* A guide to changing the clutch. */&lt;/p&gt;
&lt;hr /&gt;
&lt;div&gt;&lt;br /&gt;
== A guide to changing the clutch. ==&lt;br /&gt;
&lt;br /&gt;
It is inevitable that at some point you will have to face changing the clutch. It dips in and out of the mud on a regular basis as the bell-housing is not sealed. Eventually the clutch thrust bearing will start rattling and the action will become stiff and heavy.&lt;br /&gt;
Changing the clutch on a Jimny seems to be not for the faint hearted. It’s a very physical task and it is not pleasant struggling with the gearbox under the car, it is a very tight fit in the transmission tunnel.&lt;br /&gt;
&lt;br /&gt;
No special tools are required, but a good toolkit is needed. You will need extension bars for a socket set as some of the bolts are well hidden and difficult to access.&lt;br /&gt;
A breaker bar is also needed as some bolts are very tight.&lt;br /&gt;
&lt;br /&gt;
If this hasn’t put you off then its time to start work. It goes without saying that you should jet-wash the underside of the car if possible to remove as much of the muck before it drops on you!&lt;br /&gt;
There are two ways of changing the clutch, one is to take the engine and gearbox out and the other is to drop the gearbox off. The Suzuki factory manual suggests the gearbox dropping method so that is the way I have gone.&lt;br /&gt;
&lt;br /&gt;
The factory manual suggests it is not necessary to remove the transfer box, but I have removed it as you will need all the space you can get, I thoroughly recommend that you also remove the transfer box.&lt;br /&gt;
&lt;br /&gt;
If you have the luxury of a bit of time then spray the visible bolts with WD40 a day or so before. In particular you should try and spray the bolts holding the exhaust front section and the bolts around the gearbox housing as these are difficult.&lt;br /&gt;
&lt;br /&gt;
Starting inside the car it is necessary to remove both the gear lever and the transfer box lever.&lt;br /&gt;
&lt;br /&gt;
To remove the gearbox lever you have to remove the centre console. This is held on by four screws on the side at the front and back.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 1. Removing the Centre Console.png|thumb|left|250px|Figure 1. Removing the Centre Console]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
The console then lifts out. Mine was more of a problem as I have a switch panel fitted so I then needed to remove the gearlever before the console would come completely away, but this has to be done at some point anyway. Pull the gaiter away to reveal the three bolt heads around the base of the gearlever, undo the bolts and carefully lift out the gearstick, note that there is a small spring and a cup that should not be lost!&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 2. Removing the Gearlever.png|thumb|left|250px|Figure 2. Removing the Gearlever]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
With the console removed you will then see a frame that holds in a second gaiter. Simply undo the bolts and lift the frame clear.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 3. Removing the lower Gaiter.png|thumb|left|250px|Figure 3. Removing the lower Gaiter]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
If you are removing the Transfer Box then you need to remove the gaiter etc. around the Transfer Box Level. First locate the small screw at the rear of the transfer knob and remove it.&lt;/div&gt;</summary>
		<author><name>Leftcase</name></author>
	</entry>
	<entry>
		<id>https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_03_-_removing_the_lower_gaiter.png&amp;diff=591</id>
		<title>File:Clutch replacement guide - figure 03 - removing the lower gaiter.png</title>
		<link rel="alternate" type="text/html" href="https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_03_-_removing_the_lower_gaiter.png&amp;diff=591"/>
		<updated>2016-06-03T19:01:17Z</updated>

		<summary type="html">&lt;p&gt;Leftcase: &lt;/p&gt;
&lt;hr /&gt;
&lt;div&gt;&lt;/div&gt;</summary>
		<author><name>Leftcase</name></author>
	</entry>
	<entry>
		<id>https://www.bigjimny.com/mediawiki/index.php?title=Clutch_replacement&amp;diff=590</id>
		<title>Clutch replacement</title>
		<link rel="alternate" type="text/html" href="https://www.bigjimny.com/mediawiki/index.php?title=Clutch_replacement&amp;diff=590"/>
		<updated>2016-06-03T18:58:02Z</updated>

		<summary type="html">&lt;p&gt;Leftcase: &lt;/p&gt;
&lt;hr /&gt;
&lt;div&gt;&lt;br /&gt;
== A guide to changing the clutch. ==&lt;br /&gt;
&lt;br /&gt;
It is inevitable that at some point you will have to face changing the clutch. It dips in and out of the mud on a regular basis as the bell-housing is not sealed. Eventually the clutch thrust bearing will start rattling and the action will become stiff and heavy.&lt;br /&gt;
Changing the clutch on a Jimny seems to be not for the faint hearted. It’s a very physical task and it is not pleasant struggling with the gearbox under the car, it is a very tight fit in the transmission tunnel.&lt;br /&gt;
&lt;br /&gt;
No special tools are required, but a good toolkit is needed. You will need extension bars for a socket set as some of the bolts are well hidden and difficult to access.&lt;br /&gt;
A breaker bar is also needed as some bolts are very tight.&lt;br /&gt;
&lt;br /&gt;
If this hasn’t put you off then its time to start work. It goes without saying that you should jet-wash the underside of the car if possible to remove as much of the muck before it drops on you!&lt;br /&gt;
There are two ways of changing the clutch, one is to take the engine and gearbox out and the other is to drop the gearbox off. The Suzuki factory manual suggests the gearbox dropping method so that is the way I have gone.&lt;br /&gt;
&lt;br /&gt;
The factory manual suggests it is not necessary to remove the transfer box, but I have removed it as you will need all the space you can get, I thoroughly recommend that you also remove the transfer box.&lt;br /&gt;
&lt;br /&gt;
If you have the luxury of a bit of time then spray the visible bolts with WD40 a day or so before. In particular you should try and spray the bolts holding the exhaust front section and the bolts around the gearbox housing as these are difficult.&lt;br /&gt;
&lt;br /&gt;
Starting inside the car it is necessary to remove both the gear lever and the transfer box lever.&lt;br /&gt;
&lt;br /&gt;
To remove the gearbox lever you have to remove the centre console. This is held on by four screws on the side at the front and back.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 1. Removing the Centre Console.png|thumb|left|250px|Figure 1. Removing the Centre Console]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
The console then lifts out. Mine was more of a problem as I have a switch panel fitted so I then needed to remove the gearlever before the console would come completely away, but this has to be done at some point anyway. Pull the gaiter away to reveal the three bolt heads around the base of the gearlever, undo the bolts and carefully lift out the gearstick, note that there is a small spring and a cup that should not be lost!&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 2. Removing the Gearlever.png|thumb|left|250px|Figure 2. Removing the Gearlever]]&lt;/div&gt;</summary>
		<author><name>Leftcase</name></author>
	</entry>
	<entry>
		<id>https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_02_-_removing_the_gear_lever.png&amp;diff=589</id>
		<title>File:Clutch replacement guide - figure 02 - removing the gear lever.png</title>
		<link rel="alternate" type="text/html" href="https://www.bigjimny.com/mediawiki/index.php?title=File:Clutch_replacement_guide_-_figure_02_-_removing_the_gear_lever.png&amp;diff=589"/>
		<updated>2016-06-03T18:57:17Z</updated>

		<summary type="html">&lt;p&gt;Leftcase: &lt;/p&gt;
&lt;hr /&gt;
&lt;div&gt;&lt;/div&gt;</summary>
		<author><name>Leftcase</name></author>
	</entry>
	<entry>
		<id>https://www.bigjimny.com/mediawiki/index.php?title=Clutch_replacement&amp;diff=588</id>
		<title>Clutch replacement</title>
		<link rel="alternate" type="text/html" href="https://www.bigjimny.com/mediawiki/index.php?title=Clutch_replacement&amp;diff=588"/>
		<updated>2016-06-03T18:56:01Z</updated>

		<summary type="html">&lt;p&gt;Leftcase: &lt;/p&gt;
&lt;hr /&gt;
&lt;div&gt;&lt;br /&gt;
== A guide to changing the clutch. ==&lt;br /&gt;
&lt;br /&gt;
It is inevitable that at some point you will have to face changing the clutch. It dips in and out of the mud on a regular basis as the bell-housing is not sealed. Eventually the clutch thrust bearing will start rattling and the action will become stiff and heavy.&lt;br /&gt;
Changing the clutch on a Jimny seems to be not for the faint hearted. It’s a very physical task and it is not pleasant struggling with the gearbox under the car, it is a very tight fit in the transmission tunnel.&lt;br /&gt;
&lt;br /&gt;
No special tools are required, but a good toolkit is needed. You will need extension bars for a socket set as some of the bolts are well hidden and difficult to access.&lt;br /&gt;
A breaker bar is also needed as some bolts are very tight.&lt;br /&gt;
&lt;br /&gt;
If this hasn’t put you off then its time to start work. It goes without saying that you should jet-wash the underside of the car if possible to remove as much of the muck before it drops on you!&lt;br /&gt;
There are two ways of changing the clutch, one is to take the engine and gearbox out and the other is to drop the gearbox off. The Suzuki factory manual suggests the gearbox dropping method so that is the way I have gone.&lt;br /&gt;
&lt;br /&gt;
The factory manual suggests it is not necessary to remove the transfer box, but I have removed it as you will need all the space you can get, I thoroughly recommend that you also remove the transfer box.&lt;br /&gt;
&lt;br /&gt;
If you have the luxury of a bit of time then spray the visible bolts with WD40 a day or so before. In particular you should try and spray the bolts holding the exhaust front section and the bolts around the gearbox housing as these are difficult.&lt;br /&gt;
&lt;br /&gt;
Starting inside the car it is necessary to remove both the gear lever and the transfer box lever.&lt;br /&gt;
&lt;br /&gt;
To remove the gearbox lever you have to remove the centre console. This is held on by four screws on the side at the front and back.&lt;br /&gt;
&lt;br /&gt;
[[File:Figure 1. Removing the Centre Console.png|thumb|left|250px|Figure 1. Removing the Centre Console]]&lt;br /&gt;
&amp;lt;br clear=all&amp;gt;&lt;br /&gt;
&lt;br /&gt;
The console then lifts out. Mine was more of a problem as I have a switch panel fitted so I then needed to remove the gearlever before the console would come completely away, but this has to be done at some point anyway. Pull the gaiter away to reveal the three bolt heads around the base of the gearlever, undo the bolts and carefully lift out the gearstick, note that there is a small spring and a cup that should not be lost!&lt;/div&gt;</summary>
		<author><name>Leftcase</name></author>
	</entry>
</feed>