×
BigJimnyMeet (North) 2024 (12 Jan 2024)
BigJimnyMeet 2024
14th July 2024
Parkwood Nr. Leeds
14th July 2024
Parkwood Nr. Leeds
Booking now open - Discount for additional vehicles
Click HERE for details
Click HERE for details
×
A place for more technical discussions. Please make sure you post in the correct section on the site, this way it keeps the site tidy AND ensures you get a more relevant answer.
Help!!!! ABS Light ....
- ZukracerV6
- Topic Author
- Visitor
-
Public
26 Jun 2017 09:34 #182285
by ZukracerV6
Help!!!! ABS Light .... was created by ZukracerV6
Morning,
I am starting to lose the will with the ABS light on the Surf. No matter what I do, I cannot get the ABS light to go off when the engine is running. I have checked and tripled checked all of the connections, the brakes physically work great but without the ABS. The light just stays permanently on.
The vehicle is 95% finished but I cannot not pass the IVA test with the ABS light on!!!!
I have spent hours researching the diagnostic trouble codes and hours lying under the dash trying to find the connector behind the glove box. It simply does not exist! Does a 2009 Jimny even have this connector? Can someone post some pictures if they have a 2009 or similar aged Jimny showing this connector? None of the workshop manuals I have relate to the wiring from a 2009 Jimny.
Really need some help!
Thanks
Sam
I am starting to lose the will with the ABS light on the Surf. No matter what I do, I cannot get the ABS light to go off when the engine is running. I have checked and tripled checked all of the connections, the brakes physically work great but without the ABS. The light just stays permanently on.
The vehicle is 95% finished but I cannot not pass the IVA test with the ABS light on!!!!
I have spent hours researching the diagnostic trouble codes and hours lying under the dash trying to find the connector behind the glove box. It simply does not exist! Does a 2009 Jimny even have this connector? Can someone post some pictures if they have a 2009 or similar aged Jimny showing this connector? None of the workshop manuals I have relate to the wiring from a 2009 Jimny.
Really need some help!
Thanks
Sam
Please Log in or Create an account to join the conversation.
26 Jun 2017 13:13 #182288
by Keithy
Replied by Keithy on topic Help!!!! ABS Light ....
Is it not to the right of the bonnet release? pointing straight down.
Please Log in or Create an account to join the conversation.
- ZukracerV6
- Topic Author
- Visitor
-
Public
26 Jun 2017 15:50 #182294
by ZukracerV6
Replied by ZukracerV6 on topic Help!!!! ABS Light ....
There is a white 3 pin connector on the drivers side with 2 black cables and 1 white but when I have had a fiddle with it, I just blew the fuse for the radio!
Please Log in or Create an account to join the conversation.
26 Jun 2017 16:03 #182295
by Keithy
Replied by Keithy on topic Help!!!! ABS Light ....
Oh 3 pin I have no idea what it is.....I thought you wanted the OBD connector.
Please Log in or Create an account to join the conversation.
- ZukracerV6
- Topic Author
- Visitor
-
Public
26 Jun 2017 17:40 #182304
by ZukracerV6
Replied by ZukracerV6 on topic Help!!!! ABS Light ....
No, I'm looking for the ABS diognositc connector.
I've had a mate from a garage call around with a reader and its picked up one error code from the ABS system C1016 brake circuit? Any ideas?
I've had a mate from a garage call around with a reader and its picked up one error code from the ABS system C1016 brake circuit? Any ideas?
Please Log in or Create an account to join the conversation.
26 Jun 2017 18:11 #182308
by Keithy
Replied by Keithy on topic Help!!!! ABS Light ....
Google says brake light switch.....my brothers ABS warning light was his bulb
Please Log in or Create an account to join the conversation.
Less
More
- Posts: 1936
- Thank you received: 554
- Points: 7523.00
26 Jun 2017 18:31 #182310
by Riccy
J999 MNY, ULYSSES M18 VVT with ITB's Dyno tested at 130hp
Pickup/tipper, R7me gearbox & 6.4 Rocklobster, 31" Toyo MT, 2x ARB air locker 3.9 diffs in braced axles, 6" total lift, Floating rear conversion, Raptor painted, CB, Recaro's, Caged, etc, etc...
www.youtube.com/user/riclemus
Replied by Riccy on topic Help!!!! ABS Light ....
Its probably one of the sensors. Do you have a workshop manual as i think there is a way of testing to find out.
Possibly the resistance values of the individual sensors would point to a faulty one? The sensors all unplug from the abs controller which is near the screenwash bottle. I would test them with a multimeter and see if theres any large differences between them. There will be some small differences between them due to wire lengths, but that should be negligible. [plz note - this is a guess but easy to test without replacing anything or spending hours]
Possibly the resistance values of the individual sensors would point to a faulty one? The sensors all unplug from the abs controller which is near the screenwash bottle. I would test them with a multimeter and see if theres any large differences between them. There will be some small differences between them due to wire lengths, but that should be negligible. [plz note - this is a guess but easy to test without replacing anything or spending hours]
J999 MNY, ULYSSES M18 VVT with ITB's Dyno tested at 130hp
Pickup/tipper, R7me gearbox & 6.4 Rocklobster, 31" Toyo MT, 2x ARB air locker 3.9 diffs in braced axles, 6" total lift, Floating rear conversion, Raptor painted, CB, Recaro's, Caged, etc, etc...
www.youtube.com/user/riclemus
Please Log in or Create an account to join the conversation.
- ZukracerV6
- Topic Author
- Visitor
-
Public
27 Jun 2017 21:08 #182345
by ZukracerV6
Replied by ZukracerV6 on topic Help!!!! ABS Light ....
All the sensor are working, I have my new scanner arriving tommrrrow so so I can spend a bit more time working on the problem and trying to get the abs light to switch off
Please Log in or Create an account to join the conversation.
- Daniel30
- Visitor
-
Public
27 Jun 2017 22:09 #182348
by Daniel30
Replied by Daniel30 on topic Help!!!! ABS Light ....
Good luck
Maybe PM Rhinoman think he's a bit hot on the electrical side if a Jim
Could be wrong though
Maybe PM Rhinoman think he's a bit hot on the electrical side if a Jim
Could be wrong though
Please Log in or Create an account to join the conversation.
28 Jun 2017 05:20 - 28 Jun 2017 05:22 #182353
by mlines
Martin
2003 M13 early KAP build.
3" Trailmaster lift with 1.5 Spacers on front
Customised winch bumper and roll cage
235/85R16 Maxxis Bighorns on 16" Rims, 4:1 Rocklobster, Rear ARB locker and on-board air
Corrected arms all-round, rear disks, Recaro seats and harnesses
Replied by mlines on topic Help!!!! ABS Light ....
Martin
2003 M13 early KAP build.
3" Trailmaster lift with 1.5 Spacers on front
Customised winch bumper and roll cage
235/85R16 Maxxis Bighorns on 16" Rims, 4:1 Rocklobster, Rear ARB locker and on-board air
Corrected arms all-round, rear disks, Recaro seats and harnesses
Last edit: 28 Jun 2017 05:22 by mlines.
The following user(s) said Thank You: ZukracerV6
Please Log in or Create an account to join the conversation.
- ZukracerV6
- Topic Author
- Visitor
-
Public
28 Jun 2017 14:37 #182363
by ZukracerV6
Replied by ZukracerV6 on topic Help!!!! ABS Light ....
Martin, your right on the money!
I had found that page you posted last night, and after some real head scratching and then I started to realise the only thing I had done different to the standard Jimny was fit LED bulbs. I had done this because the rear tail lights are sealed behind a perspex cover and very tricky to access. The idea being LED's have a less likely chance of failing etc! Little did I know it was going to cause weeks of sleepless nights!
A little googling late last night, found several posts about LED lights and ABS's warning lights on Asian cars. It seems that's the ECU carries out a check on the brake light circuit to ensure its working and looks for a slight load from the traditional incandescent bulbs but with LED's its cant pick up any resistance/load and goes into a fault mood switching the ABS light on!!!
Fitted a 50w resistor on the brake light circuit and ABS warning light now switches off!
With out my mates professional code reader, I would never have looked at the LED's and brake light circuit.
Sounds like you have come across this problem before?
Sam
I had found that page you posted last night, and after some real head scratching and then I started to realise the only thing I had done different to the standard Jimny was fit LED bulbs. I had done this because the rear tail lights are sealed behind a perspex cover and very tricky to access. The idea being LED's have a less likely chance of failing etc! Little did I know it was going to cause weeks of sleepless nights!
A little googling late last night, found several posts about LED lights and ABS's warning lights on Asian cars. It seems that's the ECU carries out a check on the brake light circuit to ensure its working and looks for a slight load from the traditional incandescent bulbs but with LED's its cant pick up any resistance/load and goes into a fault mood switching the ABS light on!!!
Fitted a 50w resistor on the brake light circuit and ABS warning light now switches off!
With out my mates professional code reader, I would never have looked at the LED's and brake light circuit.
Sounds like you have come across this problem before?
Sam
Please Log in or Create an account to join the conversation.
- Daniel30
- Visitor
-
Public
28 Jun 2017 15:46 #182365
by Daniel30
Replied by Daniel30 on topic Help!!!! ABS Light ....
weldon that man
Please Log in or Create an account to join the conversation.
Time to create page: 0.153 seconds