×
BigJimnyMeet (North) 2024 (12 Jan 2024)
BigJimnyMeet 2024
14th July 2024
Parkwood Nr. Leeds
14th July 2024
Parkwood Nr. Leeds
Booking now open - Discount for additional vehicles
Click HERE for details
Click HERE for details
×
A place for more technical discussions. Please make sure you post in the correct section on the site, this way it keeps the site tidy AND ensures you get a more relevant answer.
Re:Wheel questions
- Bazh1
- Topic Author
- Visitor
-
Public
06 Jun 2020 20:56 #223325
by Bazh1
Wheel questions was created by Bazh1
I'm going to order some steel wheels for my mud tires, do I need new wheel nuts, or do the alloy ones work, also a few people recommend the wheel balence powder / beads, do you have a link to a quality product. Thanks Barry
Please Log in or Create an account to join the conversation.
Less
More
- Posts: 8814
- Thank you received: 1761
- Points: 36277.00
07 Jun 2020 08:36 #223335
by Lambert
Temeraire (2018 quasar grey automatic)
One of the last 200ish of the gen3s, probably.
ADOS Attention Deficit Ooooh Shiny!
Replied by Lambert on topic Wheel questions
Devon 4x4 supply balance beads that seem to be well reviewed. Assuming that the new wheels have the same seat profile tapers and the studs don't top out the domes on the nuts. Yes. But for the cost of a second set of nuts I would have a specific set, it saves worry.
Temeraire (2018 quasar grey automatic)
One of the last 200ish of the gen3s, probably.
ADOS Attention Deficit Ooooh Shiny!
Please Log in or Create an account to join the conversation.
- jackonlyjack
- Offline
- Platinum Member
-
Registered
Less
More
- Posts: 2911
- Thank you received: 653
- Points: 8466.00
07 Jun 2020 08:54 #223339
by jackonlyjack
Replied by jackonlyjack on topic Wheel questions
I have balance beads fitted in both sets of tyres i use
Work fine in BFG KM2's 225/75/16
But not so good in my extreme retreaded mud's 195/80/16
This could be down to the tyres,slight death wobble 40-45mph
No wobble with the bigger BFG's
Work fine in BFG KM2's 225/75/16
But not so good in my extreme retreaded mud's 195/80/16
This could be down to the tyres,slight death wobble 40-45mph
No wobble with the bigger BFG's
Please Log in or Create an account to join the conversation.
07 Jun 2020 10:24 #223343
by mlines
Martin
2003 M13 early KAP build.
3" Trailmaster lift with 1.5 Spacers on front
Customised winch bumper and roll cage
235/85R16 Maxxis Bighorns on 16" Rims, 4:1 Rocklobster, Rear ARB locker and on-board air
Corrected arms all-round, rear disks, Recaro seats and harnesses
Replied by mlines on topic Re:Wheel questions
For most Gen3 Jimnys, the steel and alloy wheel nuts are the same.
However for aftermarket wheels you will need nuts that match the chamfer on the wheels
Sent from my Pixel 2 XL using Tapatalk
However for aftermarket wheels you will need nuts that match the chamfer on the wheels
Sent from my Pixel 2 XL using Tapatalk
Martin
2003 M13 early KAP build.
3" Trailmaster lift with 1.5 Spacers on front
Customised winch bumper and roll cage
235/85R16 Maxxis Bighorns on 16" Rims, 4:1 Rocklobster, Rear ARB locker and on-board air
Corrected arms all-round, rear disks, Recaro seats and harnesses
Please Log in or Create an account to join the conversation.
- Bazh1
- Topic Author
- Visitor
-
Public
10 Jun 2020 17:56 #223458
by Bazh1
Replied by Bazh1 on topic Re:Wheel questions
Thanks everyone.
Please Log in or Create an account to join the conversation.
Time to create page: 0.103 seconds