×
Search (23 Feb 2018)

A trial enhanced search facility has been enabled. Please use the Google Custom Search above.

× A place for more technical discussions. Please make sure you post in the correct section on the site, this way it keeps the site tidy AND ensures you get a more relevant answer.

Cat

More
12 Jun 2015 20:04 #145879 by troggy
Cat was created by troggy
Hi all.
Daughters 06 jim is sucking air into the cat, and/or blowing gas out.

The pipe from the manifold seems to go into cat, but has split a seam?

Whilst it does not seem about to fall off, as the pipe goes into the cat, and it is all holding up, do you have any advice on this one?

Bunged a load of gun gum round the joint, wrapped in chicken wire (as you do), but it keeps splitting.

Best wishes to you all, The trogmeister.

Sliding down a steep learning curve.

Please Log in or Create an account to join the conversation.

More
12 Jun 2015 20:07 #145880 by jackonlyjack

Please Log in or Create an account to join the conversation.

More
12 Jun 2015 20:10 - 12 Jun 2015 20:12 #145881 by troggy
Replied by troggy on topic Cat
Thanks jack, but you have not seen my welding!
Am more likely to blow a massive hole in it, or weld myself to it.

Sliding down a steep learning curve.
Last edit: 12 Jun 2015 20:12 by troggy. Reason: add comment

Please Log in or Create an account to join the conversation.

More
12 Jun 2015 20:13 #145882 by jackonlyjack
Replied by jackonlyjack on topic Cat

troggy wrote: Thanks jack, but you have not seen my welding!

probably about the same as mine lol only started to weld in march :whistle:

Please Log in or Create an account to join the conversation.

More
12 Jun 2015 20:17 #145883 by troggy
Replied by troggy on topic Cat
Yeah, it's a fine art. thanks anyway, good luck!

Sliding down a steep learning curve.

Please Log in or Create an account to join the conversation.

More
12 Jun 2015 20:18 #145884 by jackonlyjack
Replied by jackonlyjack on topic Cat
you could try J999pre on here i bet hes got a spare :)

Please Log in or Create an account to join the conversation.

More
12 Jun 2015 20:21 #145886 by troggy
Replied by troggy on topic Cat
ok, thanks for that.

Sliding down a steep learning curve.

Please Log in or Create an account to join the conversation.

More
12 Jun 2015 21:02 #145889 by j999pre
Replied by j999pre on topic Cat
Sorry too new for me

EBay time

Gold Jimny the best colour

99 Jimny G16bb w" lift ,extended hoses, caster bushes 16x 7 mods, 225 65 15 muds. radius arm protection, rear disc conversion, snorkel, tow bar and ignis sport recaros.

Please Log in or Create an account to join the conversation.

More
27 Jun 2015 22:06 #146733 by auchenblae
Replied by auchenblae on topic Cat
It will cause the Lamda reading to go out of spec and fail an MOT.

After all these years the heat has brought the carbon out of solution in the iron and you have an unweldable metal there so sorry but time for a new cat. Our 07 had one a year or so ago.

eddie

16 SZ3
07 JLX+ gone 16
99 JLX gone 07

Please Log in or Create an account to join the conversation.

More
28 Jun 2015 08:26 #146745 by funkyjimny
Replied by funkyjimny on topic Cat
Try Euro Car Parts online, they keep emailing me offers and I was surprised how cheap they are

Gary

Please Log in or Create an account to join the conversation.

  • markyp2000
  • Visitor
  • Visitor
28 Jun 2015 09:04 #146748 by markyp2000
Replied by markyp2000 on topic Cat
Take it off and get some one to weld it id rather stick with the suzuki cat than a euros crap cat

Please Log in or Create an account to join the conversation.

Moderators: funkyjimnyooky_123
Time to create page: 0.177 seconds
Powered by Kunena Forum

I hope you enjoy using this forum. Please consider making a donation towards the upkeep of this forum website.