×
Search (23 Feb 2018)

A trial enhanced search facility has been enabled. Please use the Google Custom Search above.

× A place for more technical discussions. Please make sure you post in the correct section on the site, this way it keeps the site tidy AND ensures you get a more relevant answer.

Badge positions

More
11 Jan 2018 13:47 #188283 by mlines
mlines created the topic: Badge positions
My Jimny has had a hard life and this time around we are re-building to more of a shiny princess. It has never had badges on it (probably removed almost immediately in its life as i believe it was a KAP re-build of a damaged car, the KAP build receipts are dated 6 weeks after it was registered at a dealer)

So I now have the badges to hand, can I have a couple of measurements from someone with a ruler who can pop out to their car.

1. Left Door side edge to edge of first letter of Suzuki badge
2. Door bottom edge to edge of bottom of Suzuki badge


3. Right Door side edge to edge of last letter of Jimny badge, the top point corner of the "Y"
2. Door bottom edge to edge of bottom of Jimny badge, the base of the letter "M"


Thanks

Martin

2003 M13 early KAP build.
3" Trailmaster lift with 1.5 Spacers on front
Customised winch bumper and roll cage
235/85R16 Maxxis Bighorns on 16" Rims, 4:1 Rocklobster, Rear ARB locker and on-board air
Corrected arms all-round, rear disks, Recaro seats and harnesses

Please Log in or Create an account to join the conversation.

More
11 Jan 2018 16:53 #188285 by Cameronmike
Cameronmike replied the topic: Badge positions
1.24mm
2.189mm
3.34mm
4.197mm

Please Log in or Create an account to join the conversation.

More
11 Jan 2018 18:22 - 11 Jan 2018 18:22 #188289 by mlines
mlines replied the topic: Re:RE: Badge positions

Cameronmike wrote: 1.24mm
2.189mm
3.34mm
4.197mm

Thanks, I presume you do not mean mm, more like 21.89cm etc?

Sent from my Nexus 6P using Tapatalk

Martin

2003 M13 early KAP build.
3" Trailmaster lift with 1.5 Spacers on front
Customised winch bumper and roll cage
235/85R16 Maxxis Bighorns on 16" Rims, 4:1 Rocklobster, Rear ARB locker and on-board air
Corrected arms all-round, rear disks, Recaro seats and harnesses
Last Edit: 11 Jan 2018 18:22 by mlines.

Please Log in or Create an account to join the conversation.

More
11 Jan 2018 19:33 #188290 by Cameronmike
Cameronmike replied the topic: Re:RE: Badge positions
na sorry is mm, just the 2.189mm would be the 2. to correspond to the second lot of measurements and then the 189mm, bit unclear now that I look at it.

Please Log in or Create an account to join the conversation.

More
11 Jan 2018 21:45 #188292 by mlines
mlines replied the topic: Re:RE: Re:RE: Badge positions

Cameronmike wrote: na sorry is mm, just the 2.189mm would be the 2. to correspond to the second lot of measurements and then the 189mm, bit unclear now that I look at it.

Great, I see now

Many thanks for sorting for me

Martin

Sent from my Nexus 6P using Tapatalk

Martin

2003 M13 early KAP build.
3" Trailmaster lift with 1.5 Spacers on front
Customised winch bumper and roll cage
235/85R16 Maxxis Bighorns on 16" Rims, 4:1 Rocklobster, Rear ARB locker and on-board air
Corrected arms all-round, rear disks, Recaro seats and harnesses

Please Log in or Create an account to join the conversation.

Moderators: funkyjimnyooky_123
Time to create page: 0.095 seconds
Powered by Kunena Forum

I hope you enjoy using this forum. Please consider making a donation towards the upkeep of this forum website.