×
BigJimnyMeet (North) 2024 (12 Jan 2024)


BigJimnyMeet 2024

14th July 2024
Parkwood Nr. Leeds

Booking now open - EARLY BIRD DISCOUNTED PRICE

Click HERE for details

× A place for general chat about the Jimny. Please make sure you post in the correct section on the site, this way it keeps the site tidy AND ensures you get a more relevant answer.

Suppliers/Dealers or anyone selling with a commercial view in mind CANNOT post here unless responding to a specific request of a member in a "wanted" post.

Suppliers include people "breaking for spares" on a regular basis, when purchasing spares members should ask a supplier what they contribute to the running of the forum particularly if contacted by a Private Message

Suppliers or Members who have contributed to the forum can be identifed by the
logo.

4wd vacuum but hubs not engaging

More
30 Oct 2017 16:40 #185645 by Bilmin
Hello all

My jimny has solid green light on dash when I push 4wd button and it goes off when I press 2wd.. I have checked all vacuum hoses and no leaks, I can engage disengage hubs through the system by using manual hand pump attached to vacuum down pipes under bonnet, so def pipes are ok.. when I press 4wd the forward shaft spins and drive shafts at both sides spin as they should... I’m thinking it’s electrical switch/ solenoid? Anyone any ideas before I have a meltdown! Lol.... thankyou

Please Log in or Create an account to join the conversation.

More
03 Nov 2017 14:35 #185789 by asypeer
Check the wires on the transfer case

Please Log in or Create an account to join the conversation.

  • florinelu07
  • Visitor
  • Visitor
    Public
07 Nov 2017 12:28 #185945 by florinelu07
Replied by florinelu07 on topic 4wd vacuum but hubs not engaging
1.Check vacuum switch under the fuse box.
It is responsible for the error - faulty switch or vacuum leak.
Temporary solution is to remove the connector from it and insert a bridge wire into the connector - it should fool the system and confirm that vacuum is ok an allow you to switch modes.

IT IS JUST TEMPORARY SOLUTION.

2.If still not working, than it's the transfer case switch bulb that is causing issues.
3.Last (but not least) you should check the wiring.

Please Log in or Create an account to join the conversation.

  • Lambert
  • Lambert's Avatar
  • Offline
  • Moderator
  • Moderator
    Registered
  • The quickest Jimny in Harrogate...(that I own)
More
07 Nov 2017 13:00 #185949 by Lambert
A solid green when it 4x4? That's normal. No lights in 2x4 is also normal. Flashing green means something is not working properly. Same with orange for low range, solid good, flashing bad.

Temeraire (2018 quasar grey automatic)
One of the last 200ish of the gen3s, probably.
ADOS Attention Deficit Ooooh Shiny!

Please Log in or Create an account to join the conversation.

  • Lambert
  • Lambert's Avatar
  • Offline
  • Moderator
  • Moderator
    Registered
  • The quickest Jimny in Harrogate...(that I own)
More
07 Nov 2017 13:32 #185953 by Lambert
Also have you taken the hubs off and given them a clean and light lube?

Temeraire (2018 quasar grey automatic)
One of the last 200ish of the gen3s, probably.
ADOS Attention Deficit Ooooh Shiny!

Please Log in or Create an account to join the conversation.

  • florinelu07
  • Visitor
  • Visitor
    Public
07 Nov 2017 14:03 #185955 by florinelu07
Replied by florinelu07 on topic 4wd vacuum but hubs not engaging
One of my hub lock had the membrane with issues, therefore no vacuum was kept (both circuits).

Replaced & fixed. Now I get -10PSI of vacuum.

Please Log in or Create an account to join the conversation.

Time to create page: 0.140 seconds
Powered by Kunena Forum

I hope you enjoy using this forum. Please consider making a donation towards the upkeep of this forum website.

We use cookies to give you the best online experience. Please let us know if you agree to all of these cookies. Accepting the Cookies also accepts the Disclaimers for the website.